Avaya AA1419074-E6 Datenblatt

Installation — SFPs and XFPsAvaya Ethernet Routing Switch 5000Series6.2NN47200-302, 03.02December 2010

• Leave all components in their ESD-safe packaging until installation, and use only a static-shielding bag for all storage, transport, and handling.•

Caution:Risk of equipment damageDo not crush fiber optic cable. If fiber optic cable is in the same tray or duct with large, heavyelectrical cables,

When you insert a connector ferrule into a connector or adapter, ensure that the ferrule tipdoes not touch the outside of the mating connector or adap

4. Dry the connector surfaces by applying canned air.5. Inspect the connector to ensure it is clean and undamaged.To prevent contamination, do not tou

Important:Do not let the IPA evaporate; wipe it dry immediately. Alcohols can leave a residuethat is difficult to remove.5. Blow dry the connector su

4. Remove lint by blowing compressed air into the optical port.5. Reconnect the optical connector and check for proper function.If you are not reinsta

Electrostatic alert:PRECAUCIÓNRiesgo de daño del equipoPara prevenir el daño producido por una descarga electrostática, use siempre una pulseraanties

Caution:CUIDADORisco de danos ao equipamentoSomente pessoal treinado pode instalar este produto. Caution:ATTENZIONERischio di danni all’apparecchiatu

Warning:ADVERTENCIARiesgo de lesión en los ojos por láser El equipo de fibra óptica puede emitir una luz láser oinfrarroja que dañe sus ojos. Nunca m

Chapter 4: Small form factor pluggabletransceiversThis section describes how to select and install small form factor pluggable (SFP) transceivers.Use

© 2010 Avaya Inc.All Rights Reserved.NoticeWhile reasonable efforts have been made to ensure that theinformation in this document is complete and accu

Job aidThe following table describes the reach provided by various SFPs. This table is informationalonly—not all Avaya Ethernet switching and routing

Model and connector Product number Description1000BASE-SX (LC) AA1419013-E5 850 (nm), up to 275 or 550 m1000BASE-SX (MT-RJ) AA1419014-E5 850 nm, up to

Model Product number Description1000BASE-ZX CWDMAA1419061-E6 toAA1419068-E61470 nm to 1630 nm, up to 70km1000BASE-BX (LC type) AA1419069-E6,AA1419070-

To prevent damage from electrostatic discharge, always wear an antistatic wrist strapconnected to an ESD jack. Caution:Risk of equipment damageOnly tr

The following figure shows the 1000BASE-SX MT-RJ SFP. Push the tab to release the device.The following figure shows the wrap-around latch-type extract

PrerequisitesWear an antistatic wrist strap. Warning:Risk of eye injury by laserFiber optic equipment can emit laser or infrared light that can injure

Small form factor pluggable transceivers26 Installation — SFPs and XFPs December 2010

Chapter 5: SFP specificationsThis section provides technical specifications for the supported small form factor pluggable (SFP) models.Use this infor

SFP labelsThe Avaya label on a typical SFP contains an Avaya serial number, a bar code, a manufacturercode, an interface type, and a part number.Figur

100BASE-FX SFP specificationsThe 100BASE-FX SFP provides 100 Mb/s Ethernet Carrier Sense Multiple Access withCollision Detection (CSMA-CD) connectivit

ContentsChapter 1: New in this release...5Features...

Important:The switch displays the interface speed of the T1/E1 SFP as a 100 Mb/s connection eventhough the interface is operating at the appropriate

Pin Description3 Receive shield4 Transmit ring5 Transmit tip6 Transmit shield7 Not used8 Not usedThe T1 equipment at the far end of the T1 connection

Terminal A Terminal BPin Description Pin Description6 Transmit shield 6 Receive shield7 Not used 7 Not used8 Not used 8 Not usedYou can use a short cr

Important:You must configure the T1 SFP module to match the parameters of the T1 equipment at thefar end. If you must change the parameters, contact

Table 9: IEEE 802.3z 1000BASE-SX (LC) SFP specificationsParameter SpecificationsConnectors Duplex LCCabling• 62.5 µm MMF optic cable• 50 µm MMF optic

Parameter SpecificationsTransmitter characteristicsLaunch power – 10 to – 4.0 dBmReceiver characteristicsReceiver sensitivity – 17 dBmMaximum input po

1000BASE-XD CWDM SFP specificationsThe 1000BASE-XD SFPs provides CWDM gigabit Ethernet connectivity using single modefiber. These SFPs support full-du

Important:For the 70 km CWDM SFPs, a minimum attenuation of 10 dB must be present between thetransmitter and receiver.Table 13: 1000BASE-ZX CWDM (70

Parameter SpecificationsLaunch power – 9.5 to -4.0 dBmReceiver characteristicsReceiver sensitivity – 17 dBmMaximum receiver power 0 dBm1000BASE-LX DDI

Table 16: 1000BASE-XD DDI 1310 nm SFP specificationsParameter SpecificationsMaximum electrical power consumption 1.0 WConnectors Duplex LCCabling SMF,

1000BASE-EX DDI SFP specifications...45Chapter

Parameter SpecificationTransmitter characteristicsLaunch power – 2.0 to 3.0 dBmReceiver characteristicsReceiver sensitivity – 24 dBmMaximum receiver p

1000BASE-XD DDI CWDM SFP specificationsThe following table describes specifications for 1000BASE-XD DDI CWDM SFPs numberedAA1419053-E6 to AA1419060-E6

To prevent damage to the optical receiver, ensure that at least 8 dB of attenuation is presentbetween the transmit and receive ports.Table 20: 1000BAS

while the mating model transmits at 1490 nm and receives at 1310 nm. You can only connect amating pair.You can use 1000BASE-BX SFPs to double the numb

You can use 1000BASE-BX SFPs to double the number of your fiber links. For example, if youhave 20 installed fiber pairs with 20 conventional ports con

1000BASE-EX DDI SFP specificationsThe following table describes the 1000BASE-EX DDI SFP. This SFP operates at 1550 nm andhas a reach of up to 120 km.

SFP specifications46 Installation — SFPs and XFPs December 2010

Chapter 6: 10 Gigabit small form factorpluggable transceiversThis section describes how to install and remove 10 gigabit small form factor pluggable

All Avaya XFPs use Lucent connectors (LC) to provide precision keying and low interfacelosses.The following table lists and describes the Avaya XFP mo

Installing an XFPInstall an XFP to provide a 10 gigabit Ethernet interface between the switch and other networkdevices.Installing an XFP takes approxi

Chapter 1: New in this releaseThe following sections detail what’s new in Avaya Ethernet Routing Switch 5000 Series Installation —SFPs, NN47200-302 f

4. Remove the dust cover from the XFP optical bores and insert the fiber optic cable.Job aidDepending on the transceiver manufacturer, your XFP transc

Procedure steps1. Disconnect the network fiber cable from the XFP connector.2. Affix a dust cover over the optical connector.3. Pull the bail mechanis

10 Gigabit small form factor pluggable transceivers52 Installation — SFPs and XFPs December 2010

Chapter 7: XFP specificationsThis section provides technical specifications for the supported 10 gigabit SFP (XFP) models. Use thesespecifications to

Figure 3: XFP labelGeneral XFP specificationsThe following table describes general XFP specifications.Table 24: General XFP specificationsParameter Sp

Caution:Risk of equipment damageTo prevent damage to the optical receiver, ensure that at least 1 dB of attenuation is presentbetween the transmit an

Parameter SpecificationsMaximum receiver sensitivity in OMA – 11.1 dBmMaximum receiver reflectance – 12 dBStressed receiver sensitivity in OMA – 7.5 d

Parameter SpecificationsAverage launch power – 6.5 to 0.5 dBmPeak launch power 3 dBmRoot-mean-square spectral width 2.4 to 4 nmLaunch power in OMA – 4

Fiber type (core diameterand OFL bandwidth)Range Maximum channelinsertion loss• 400 MHz-km at 850 nm• 400 MHz-km at 1300 nm50 μm (ISO/IEC OM3)• 1500 M

Table 29: IEEE 802.3ae 10GBASE-LR/LW XFP specificationsParameter SpecificationsMTBF 675 000 hoursCenter wavelength range 1260 to 1355 nm; 1310 nm nomi

New in this release6 Installation — SFPs and XFPs December 2010

Examples of an OFF transmitter are as follows: no power supplied to the PDM, laser shutdownfor safety conditions, activation of a PMD_global_transmit_

Parameter SpecificationsAverage receive power for BER 10-12– 15.8 dBm to – 1.0 dBmMaximum receive power for damage 4.0 dBmMaximum receiver sensitivity

Parameter SpecificationsCenter wavelength range 1530 to 1565 nm; nominal 1550 nmSide mode suppression ratio (minimum) 30 dBAverage launch power 0 to 4

Chapter 2: IntroductionThis document provides installation instructions and technical specifications for Small Form FactorPluggable (SFP) transceiver

Introduction8 Installation — SFPs and XFPs December 2010

Chapter 3: Safety and equipment careinformationThis section contains important safety and regulatory information. Read this section before you instal