Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services Bedienungsanleitung Seite 223
- Seite / 390
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Customizing OSPF Services
308627-14.20 Rev 00
6-39
Using the BCC
To configure a neighbor on an NBMA interface, go to an OSPF interface prompt
(for example,
box; eth 2/2; ip/2.2.2.2/255.255.0.0; ospf
) and enter:
neighbor
<ip_address>
ip_address
specifies the IP address (in dotted-decimal notation) of the neighbor
for this NBMA interface.
To change the default values for a neighbor, enter:
<parameter> <value>
Table 6-7 lists the parameters and values that you can enter.
Examples
The following command sequence sets the OSPF interface type to NBMA,
configures a neighbor for NBMA interface 2.2.2.2, and changes the router priority
to 3:
ospf/2.2.2.2#
type nbma
ospf/2.2.2.2#
neighbor 3.3.3.3
neighbor/3.3.3.3#
priority 3
neighbor/3.3.3.3#
The following command sequence disables and reenables neighbor 3.3.3.3:
neighbor/3.3.3.3#
state disabled
neighbor/3.3.3.3#
state enabled
Table 6-7. BCC Neighbor Parameters for an NBMA Interface
Parameter Values Function
priority 1 (default)
0 through 255
Specifies a router priority for this NBMA
interface. A value of 255 is the highest priority;
a value of 0 makes this router ineligible to be
the designated router on this network.
state enabled (default)
disabled
Enables or disables this neighbor configuration
for this NBMA interface.
- Configuring IP, ARP, RARP 1
- RIP, and OSPF Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308627-14.20 Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 33
- OSPF Neighbors 37
- Neighbor Adjacencies 37
- Designated Routers 38
- AS External Routes 38
- OSPF Areas 39
- OSPF Router Types 41
- OSPF Implementation Notes 41
- Router Discovery Protocol 42
- Route Preferences 43
- Route Weights 44
- Figure 1-7. IP Routing Table 46
- IP Traffic Filters 50
- Chapter 2 51
- Starting IP Services 51
- Starting RIP 53
- Starting OSPF 54
- Starting Router Discovery 54
- Adding RIP to an IP Interface 57
- Starting RARP 59
- Chapter 3 61
- Setting the ICMP Error Limit 75
- Caution: 81
- Customizing an IP Interface 84
- Specifying a MAC Address 97
- IP0012A 99
- Using the BCC 100
- Using Site Manager 100
- Configuring an SMDS Address 102
- (continued) 103
- Deleting IP from an Interface 106
- Defining a Static Route 117
- (continued) 119
- Defining a Default Route 121
- Customizing Router Discovery 122
- Choosing a Broadcast Type 124
- Chapter 4 129
- Customizing ARP 130
- Customizing Global ARP 131
- Figure 4-1. Proxy ARP Example 137
- Customizing RARP 141
- Deleting RARP Globally 144
- Chapter 5 145
- Customizing RIP Services 145
- Setting the RIP Diameter 146
- Customizing a RIP Interface 147
- Selecting the RIP Version 148
- ) and enter: 149
- Specifying the Update Mode 153
- Sending Triggered Updates 155
- Receiving RIP Updates 158
- Listening for a Default Route 161
- Defining a RIP Accept Policy 170
- Chapter 6 185
- Customizing OSPF Services 185
- Supplying an OSPF Router ID 188
- Figure 6-1. OSPF ASE Routes 193
- Setting the Holddown Timer 198
- <value> 199
- <seconds> 199
- Configuring Message Logging 200
- Changing the Area ID 205
- Specifying the Interface Type 206
- Estimating the Transit Delay 210
- Setting the Hello Interval 212
- Setting the Dead Interval 214
- Specifying the Metric Cost 217
- Specifying the MTU Size 219
- Examples 223
- Configuring Areas 226
- Configuring Authentication 229
- Configuring a Summary Route 231
- Configuring a Stub Area 233
- Transit area 244
- Policies 257
- Appendix A 263
- Site Manager Parameters 263
- IP Parameters 264
- IP Interface Parameters 266
- IP Global Parameters 280
- Static Route Parameters 289
- Adjacent Host Parameters 292
- Router Discovery Parameters 295
- RARP Parameters 297
- OSPF Parameters 298
- OSPF Global Parameters 299
- OSPF Interface Parameters 303
- OSPF Area Parameters 311
- Area Range Parameters 315
- OSPF NSSA Range Parameters 318
- RIP Parameters 324
- Manager online Help 331
- RIP Accept Policy Parameters 335
- OSPF Accept Policy Parameters 337
- Appendix B 353
- RIP Import Filters 354
- RIP Export Filters 357
- OSPF Import Filters 360
- OSPF Export Filters 363
- Appendix C 367
- Route Weight Worksheet 367
- Appendix D 371
- IP/OSPF Configuration Example 371
- Manager and the BCC 374
Verwandte Produkte und Handbücher für Software Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services
Software Avaya PeriReporter Business Communications Manager Release 6.0 Bedienungsanleitung
(133 Seiten)
(133 Seiten)
Software Avaya CS1000 Bedienungsanleitung
(180 Seiten)
(180 Seiten)
Software Avaya Digital Enchanced Cordless Telecommuncations SIP DECT Fundamentals Bedienungsanleitung
(254 Seiten)
(254 Seiten)
Software Avaya Connecting BayStack AN and ANH Platforms to a Network Bedienungsanleitung
(178 Seiten)
(178 Seiten)
Software Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Bedienungsanleitung
(148 Seiten)
(148 Seiten)
Software Avaya Configuring Traffic Filters and Protocol Prioritization Bedienungsanleitung
(162 Seiten)
(162 Seiten)
Software Avaya Nortel Business Communications Manager 450 1.0 Administration and Security Bedienungsanleitung
(200 Seiten)
(200 Seiten)
Software Avaya BCM 4.0 Bedienungsanleitung
(398 Seiten)
(398 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern