Avaya BCM50 Installationshandbuch Seite 77
- Seite / 335
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 6 Checking the installation prerequisites 77
Installation and Maintenance Guide
Chapter 6
Checking the installation prerequisites
Before you install a main unit or expansion unit, perform the following tasks:
• Determine the location for the BCM50 units, telephones, and other equipment based on space
and electrical requirements.
• Order the required trunks from the central office.
• Ensure that you have all the equipment and supplies you need to install the system.
For information about BCM50 installation prerequisites:
• Environmental requirements on page 77
• Electrical requirements on page 77
• Site telephony wiring requirements on page 78
• System equipment, supplies, and tools on page 79
Environmental requirements
Ensure you meet the installation environmental requirements. The installation area must be:
• a minimum of 4 m (13 ft.) from equipment such as photocopiers, electrical motors, and other
equipment that produces electromagnetic, radio frequency, and electrostatic interference
• within 1.5 m (5 ft.) of a three-wire grounded electrical outlet
• clean, dry, well ventilated, and free of traffic and excess dust
• within the temperature range of 5°C and 50°C (40°F and 120°F)
• from 20% to 80% non condensing relative humidity
• structurally strong and with enough space to support the BCM50 units
• a minimum of 46 cm (18 in.) from the floor
Electrical requirements
Ensure you meet the following electrical requirements:
• Power must be supplied from a non switched, unobstructed outlet within 1.5 m (5 ft.) of the
BCM50 units.
• The supplied power must be a dedicated 110 V to 120 V AC nominal (or 220 V to 240 V AC
nominal), 50 to 60 Hz, 15 A minimum service with a third-wire safety ground. The third-wire
safety ground provides shock protection and prevents electromagnetic interference.
Note: The installation area must be of sufficient height from the floor to prevent water
damage.
- BCM50 3.0 1
- Trademarks 2
- SOFTWARE LICENSE 3
- Task List 7
- 10 Task List 10
- NN40020-302 10
- Contents 11
- 18 Contents 18
- New in this release 19
- 20 New in this release 20
- Regulatory information 21
- EMI/EMC (FCC Part 15) 22
- Important safety instructions 23
- Use of a music source 24
- Enhanced 911 configuration 25
- Radio-frequency interference 25
- Additional safety information 27
- Chapter 1 29
- Symbols and text conventions 31
- Related publications 33
- How to get help 34
- Chapter 2 37
- ports and connectors 39
- Media bay modules 44
- Trunk media bay modules 45
- Global Analog Trunk Module 46
- Station media bay modules 47
- 4x16 media bay module 48
- BCM50 hardware 52
- Patch panel 53
- Wall-mount bracket 53
- BCM50 components 54
- Power supply 55
- Uninterruptable power supply 55
- Hard disk 56
- Cooling fan 57
- RJ-21 telephony connector 58
- Field-replaceable units 59
- Accessories 60
- Chapter 3 61
- LAN port LEDs 63
- Figure 30 MBM LEDs 66
- DTM LEDs 67
- BRIM LEDs 68
- Chapter 4 69
- (with integrated router) 70
- Chapter 5 73
- Chapter 6 77
- Digital loop 78
- Analog loop 78
- Basic hardware 79
- Optional equipment 79
- Other hardware and tools 79
- Chapter 7 81
- Unpacking the main unit 82
- To install the patch panel 85
- To install the WFC 90
- Attach feet here 91
- Chapter 8 95
- Unpacking the expansion unit 96
- To set GASM dip switches 98
- To set GATM dip switches 99
- To install an MBM 100
- Next step 101
- Chapter 9 103
- Connecting the expansion unit 104
- To connect an expansion unit 105
- Connecting the power supply 106
- Figure 51 Connect a UPS 107
- Wiring warnings 109
- G4x16/G8x16 112
- G8x16 MBMs 113
- Music source specifications 115
- Figure 52 Music source jack 116
- Chapter 10 119
- Installing IP phones 120
- Chapter 11 121
- Installing the ATA2 122
- To connect the ATA2 123
- Mounting the ATA2 123
- To mount the ATA2 on a wall 123
- Figure 57 ATA2 back view 124
- Mounting keyhole slots 124
- Configuring the ATA2 125
- Chapter 12 127
- Initial parameters overview 128
- Startup parameters overview 129
- Chapter 13 131
- To enter the keycodes 132
- To configure the IP address 133
- To configure the modem 133
- To select the region 134
- To initialize voice mail 134
- Chapter 14 137
- Prerequisites 138
- Accessing the BCM50 system 138
- To enter a keycode 139
- To configure IP Phones 144
- To configure SNMP settings 145
- To create user accounts 146
- Chapter 15 149
- Startup Profile requirements 150
- Configuring basic parameters 151
- Chapter 16 155
- To configure the MBM(s) 156
- Configuring modem settings 157
- Checking for software updates 157
- Configuring voice mail 157
- Customizing security policies 157
- Performing a backup 158
- Chapter 17 159
- Chapter 18 165
- To troubleshoot the main unit 166
- To test the expansion unit 166
- To test the MBM 167
- To test a station MBM 167
- To test a trunk MBM 167
- Reset to factory settings 169
- Activate the reset feature 170
- Table 32 Level 1 reset 172
- Table 33 Level 2 reset 172
- Chapter 19 173
- To shut down the system 174
- Chapter 20 175
- Removing the power supply 176
- Connect the new power supply 176
- Chapter 21 179
- Removing the main unit 180
- Installing the new main unit 181
- To connect the cables 182
- Chapter 22 183
- To remove the MBM 184
- To insert the new MBM 185
- Chapter 23 187
- Disconnecting the cables 188
- Removing the expansion unit 188
- Removing the MBM 190
- Chapter 24 193
- Special tools 194
- Opening the main unit case 194
- To open the main unit case 195
- To remove the hard disk 197
- To remove the fan 198
- Inserting the new component 199
- To insert the new hard disk 200
- Fan cable cutouts 201
- Fan cable clips 201
- To insert the new fan 202
- To insert the new router card 203
- Closing the main unit case 204
- Installing the main unit 205
- Connecting the cables 205
- Appendix A 207
- Appendix B 211
- Table 36 BRI line numbering 212
- Appendix C 213
- Table 37 LAN port wiring 214
- Appendix D 215
- Appendix E 217
- Appendix F 219
- Appendix G 221
- Appendix H 223
- Appendix I 225
- Digital interfaces 226
- Tones and cadences 227
- • Reorder, 1 kHz on page 233 228
- Functionality Attribute 237
- Market profile 237
- Russia South Africa 245
- Analog Trunk parameters 250
- GASM8 parameters 256
- GASI parameters 259
- ATA2 parameters 262
- ATA2 DR7 264
- Voicemail 265
- ISDN line services 268
- Trunk Types Description 269
- Appendix J 271
- Appendix K 275
- (Sheet 2 of 2) 276
- (Sheet 1 of 2) 277
- (Sheet 2 of 2) 278
- Appendix L 279
- Appendix M 283
- Appendix N 285
- • Reorder, 1 kHz on page 293 288
- Numerics 331
Verwandte Produkte und Handbücher für Router Avaya BCM50
Router Avaya BCM50e Bedienungsanleitung
(311 Seiten)
(311 Seiten)
Router Avaya Cable Bedienungsanleitung
(194 Seiten)
(194 Seiten)
Router Avaya FireWall-1 Bedienungsanleitung
(60 Seiten)
(60 Seiten)
Router Avaya BCM50 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Router Avaya BayRS Version 14.10 Hinweis
(42 Seiten)
(42 Seiten)
Router Avaya BayRS, BCC, and Site Manager Software Version 14.20 Fixed Anomalies Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Router Avaya FireWall-1 Bedienungsanleitung
(54 Seiten)
(54 Seiten)
Router Avaya Business Communications Manager - Administration - Remote Worker Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Router Avaya BCM50 Installationshandbuch
(295 Seiten)
(295 Seiten)
Router Avaya 1600 Series Bedienungsanleitung
(100 Seiten)
(100 Seiten)
Router Avaya BCM50e Bedienungsanleitung
(441 Seiten)
(441 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.424 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern