Avaya 6424D+M Bedienungsanleitung Seite 31
- Seite / 74
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Data Option Definitions
The following descriptions assume single-stream operation which is the case when API is not
being used. Refer to the ISDN Application Programming Interface Programmer’s Manual for
more information on single-stream and autostream.
Note that the examples used in this section assume the use of CMD mode.
Answer
Option Values: auto, manual
Applicable Data Protocols: All
Set Answer to auto if you want incoming data calls to be answered automatically. Select
manual if not. If you set Answer to manual, you can answer data calls manually if your ADM is
attached to an asynchronous data terminal by typing
y
in response to the prompt ANSWER? or
by pressing
DATA/SEND/OFF
on your voice terminal.
Interactions with DTR: If the DTR option is set to follow and Answer is set to auto, then the
ADM checks to make sure that the DTR lead is on (usually indicating that your terminal is turned
on) before automatically answering the call. If you have set the DTR option to ignore and
Answer to auto, the ADM answers data calls whether or not the DTR lead is turned on. If the
DTR option is set to follow and Answer is set to manual, the ADM will not let you manually
answer the call unless DTR is on.
Attention
Option Values: off, 3 of the same ASCII character (default = +++)
Applicable Data Protocols: All
The Attention sequence is used to take the ADM out of the Data Mode enabling you to enter
commands. The default setting is +++.
You must type the sequence rapidly (all three characters within 1.5 seconds).
Before entering the Attention sequence, there must be —at least—a one second delay after typing
your last character. Then the three characters composing the sequence must be typed within 1.5
seconds. Finally, no additional characters should be typed for one second after typing the
Attention sequence. Failure to comply with these guidelines results in the Attention sequence
characters being sent to the far-end as data.
To change the attention sequence to @@@, for example, type
set attention @
from an
attached data terminal. Note that you need only type the new character once while changing the
value.
Note: Possible values include any printable or control characters except NUL
Ctrl
-
@
,
SOH
Ctrl
-
A
, CAN
Ctrl
-
X
, NAK
Ctrl
-
U
, BS
Ctrl
-
H
, DC3
Ctrl
-
S
,
and DC1
Ctrl
-
Q
.
Data Options and Profiles 4-3
- ISDN Asynchronous Data Module 1
- Feature Package 3 1
- User Manual 1
- Contents 3
- Introduction 5
- Data Features 6
- System Dependencies 7
- Conventions of this Manual 8
- Getting Started 9
- Local Mode 10
- Data Mode 10
- 1 Press the 11
- 2 Press the 11
- 3 Press 11
- Getting Started 2-3 11
- Getting Started 2-5 13
- Making a Data Call 14
- 2 At the CMD: prompt, type 15
- Getting Started 2-7 15
- Mode Commands 16
- Using the CMD and AT Commands 17
- Using CMD Local Mode Commands 18
- Help for CMD Commands 19
- Abbreviating CMD Commands 20
- X.25 Call Options 21
- Memory Dialing 23
- Using AT Local Mode Commands 24
- AT Commands 25
- Command Application 26
- S-Registers 27
- Dialing a Voice Call 28
- Data Options and Profiles 29
- Option Possible Values 30
- Data Option Definitions 31
- Autoadjust 32
- Char.erase (Character Erase) 32
- DCD (Data Carrier Detect) 33
- DTR (Data Terminal Ready) 33
- 4-6 Chapter 4 34
- Forwarding 35
- Idle.timer 35
- Line.erase 35
- Local.cr 36
- Local.echo 36
- Local.erase 36
- Local.lf 37
- Match.speed 37
- 4-10 Chapter 4 38
- 4-12 Chapter 4 40
- 4-14 Chapter 4 42
- Data Option Profiles 43
- Storing an Active Profile, pA 46
- Activating a Stored Profile 46
- Viewing an Option Profile 47
- 4-20 Chapter 4 48
- Local Loopback Test 51
- Remote Loopback Test 52
- Self-Test 53
- Technical Information 55
- Pin 4 - Request-to-Send (CA) 56
- Pin 5 - Clear-to-Send (CB) 56
- Pin 6 - Data Set Ready (CC) 56
- Pin 7 - Signal Ground (AB) 56
- Pin 22 — Ring Indicator (CE) 57
- 6-4 Chapter 6 58
- (Continued) 59
- Terminal Displays 61
- Troubleshooting 63
- 7-2 Troubleshooting 64
- Value EIA Port Text LCD Text 68
- GLOSSARY 69
- GL-2 GLOSSARY 70
Verwandte Produkte und Handbücher für Telefone Avaya 6424D+M
Telefone Avaya T3 Bedienungsanleitung
(142 Seiten)
(142 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.491 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern