Avaya Configuring ATM and MPLS Services Bedienungsanleitung Seite 189
- Seite / 529
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Customizing Signaling
117374-C Rev 00
5-41
Modifying Control VC Traffic Parameters
You can modify the following traffic parameters for both the signaling and the
ILMI control VCs:
• Peak cell rate (PCR)
• Sustainable cell rate (SCR)
• Maximum burst size (MBS)
For additional information about traffic parameters, see “ATM Traffic Parameters”
on page 1-23.
Setting the PCR
The peak cell rate (PCR) specifies the upper traffic limit, in cells/s, that the ATM
connection can support.
By default, the PCR is set to 4716 cells/s. Table 5-2
lists the valid ranges for each
Bay Networks ATM router.
For additional information about the PCR, see “Using the PCR” on page 1-24.
Table 5-2. Valid PCR Ranges
ATM Router Range (Cells/s)
ATM ARE OC-3 SONET/SDH ILI pairs 128 to 353,207
Model 5782 Centillion MPE 128 to 353,207
ATM ARE DS-3 ILI pairs 128 to 96,000
ATM ARE E-3 ILI pairs; G.832 framing mode 128 to 80,000
ATM ARE E-3 ILI pairs; G.751 framing mode 128 to 72,000
- Configuring ATM 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117374-C Rev 00 10
- Before You Begin 23
- Text Conventions 24
- Acronyms 26
- How to Get Help 30
- Chapter 1 31
- Understanding ATM, MPOA 31
- ATM General Information 32
- Figure 1-2. ATM Cell Header 33
- Data Transmission 34
- VP = Virtual path 35
- VC = Virtual channel 35
- ATM Layers 36
- ATM0005A 39
- Data Encapsulation Methods 42
- Encapsulation Rules for PVCs 46
- PVC Access Methods 47
- SVC Access Methods 52
- Assigning ATM Addresses 52
- ATM Traffic Parameters 53
- ARP and Inverse ARP Support 57
- ATM Error Checking 57
- Converting Mb/s to Cells/s 57
- ATM Address Resolution 61
- ATM LAN Emulation Concepts 63
- LAN Emulation Components 64
- Redundant LES/BUS 65
- LAN Emulation States 66
- MPOA Logical Components 69
- MPOA Basic Elements 70
- Figure 1-15 73
- OAM Loopback 75
- OAM Alarms 75
- For More Information 76
- Chapter 2 79
- Understanding MPLS 79
- MPLS General Information 80
- MPLS System Overview 81
- Label Distribution Entity 82
- MPLS Label Management 82
- Forwarding 82
- The MPLS Network 83
- Label Switching Router 84
- Label Edge Router 84
- Supported Protocols 85
- Chapter 3 87
- Using the Bay Command Console 88
- Site Manager 88
- Defining PVC Service 90
- Defining Classical IP Service 90
- Defining LEC Service 91
- <vpi_number> 92
- <vci_number> 92
- Adding IP 93
- Adding IPX 93
- Adding PVCs 100
- Starting the MPOA Server 101
- Configuring IP 102
- Services 102
- Mapping an MPS to a LEC 105
- (continued) 106
- (continued) 107
- Configuring the MPS 108
- Redundancy 110
- Configuring 111
- Deleting ATM from the Router 115
- Starting MPLS 116
- Configuring IP Services 125
- Where to Go Next 126
- Chapter 4 127
- Customizing an ATM Interface 127
- Using the BCC 128
- Using Site Manager 129
- <integer> 147
- Chapter 5 149
- Customizing Signaling 149
- Defining Signaling 150
- Pacing Calls 173
- Table 5-2. Valid PCR Ranges 189
- Defining SSCOP/Signaling AAL 205
- Chapter 6 217
- Customizing PVC Service 217
- Records and PVCs 217
- Chapter 7 243
- Specifying an Owner 270
- Chapter 9 307
- Setting the Give Up Time 321
- Deleting an Individual MPS 325
- Chapter 10 329
- Chapter 11 333
- Customizing LDP Parameters 334
- Changing the Local IP Address 335
- Specifying a Local TCP Port 336
- Specifying a Remote TCP Port 338
- Specifying a Hold Time 340
- Setting the Receive SDU Size 358
- Accessing ATM Parameters 368
- Using the Menu Path 370
- ATM Line Parameters 372
- Site Manager Parameters 373
- ATM Interface Parameters 378
- ATM Service Record Parameters 381
- LAN Emulation Parameters 393
- LES Parameters 403
- ATM Signaling Parameters 405
- Caution: 409
- ATM ILMI Signaling Parameters 421
- ATM Signaling AAL Parameters 429
- MPOA Parameters 433
- OAM Parameters 442
- MPLS Parameters 445
- MLM Parameter 449
- Static Route Parameters 449
- Default VC Parameters 450
- NHRP Parameters 460
- ATMARP Parameters 468
- Adjacent Host Parameters 470
- <slot> 474
- <connector> 474
- <servicename> 479
- <ip_address> 481
- show dsx3 circuits 483
- show dsx3 current 484
- show dsx3 history 487
- show sonet circuits 498
- show sonet current 499
- show sonet history 502
- Appendix C 507
- NHRP Overview 508
- Editing an NHRP Record 514
- Disabling an NHRP Record 515
- Deleting NHRP 515
- Index-10 526
- Index-11 527
- Index-12 528
- Index-13 529
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring ATM and MPLS Services
Vernetzung Avaya BCM450 Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Vernetzung Avaya Configuring Ethernet, FDDI, and Token Ring Services Bedienungsanleitung
(94 Seiten)
(94 Seiten)
Vernetzung Avaya Nortel Business Communications Manager 450 1.0 Anleitung zur Fehlerbehebung
(102 Seiten)
(102 Seiten)
Vernetzung Avaya BCM 3.6 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Vernetzung Avaya Red Hat Linux 9 DHCP Server Configuration for 4600 Series IP Telephones Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Vernetzung Avaya Call Center Reporting to Reporting for Contact Center Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Vernetzung Avaya BCM 3.0 Betriebsanweisung
(28 Seiten)
(28 Seiten)
Vernetzung Avaya 1200-Series Anwendungshinweis
(44 Seiten)
(44 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(148 Seiten)
(148 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern