Avaya R2MFC Konfigurationsanleitung Seite 94
- Seite / 106
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
94 Config DIP switch settings and definitions
N0027684 01
Brazil Config 2
E1 physical characteristics
• Connector type: BNC
• Line coding: HDB3
E1 framing
Frame mode: Alternate
Register signaling
• Regret option: OFF
• End of dialing (Incoming): terminated by indication from destination switch, or by MFC
forward signal FW_EndDigits
• End of dialing (Outgoing): terminated by indication from destination switch, or by MFC
forward signal FW_EndDigits
BW_OutOfOrder B_4 FW_Digit_13 I_13 FW_Categ_15 II_15
BW_ChangOrder B_4 FW_Digit_14 I_14 FW_KD_Local II_3
FW_ReqFault I_12 FW_Digit_15 I_15 FW_KD_LnDst II_2
FW_EndDigits I_15 FW_Categ_1 II_1
Table 34 Interpretation of transmitted MFC signals (Sheet 2 of 2)
Meaning Signal Meaning Signal Meaning Signal
- R2MFC Media Bay Module 1
- Trademarks 2
- Enhanced 911 Configuration 3
- Radio-frequency Interference 3
- Hearing Aid Compatibility 4
- Important Safety Instructions 4
- Limited Warranty 7
- Warranty Repair Services 8
- After Warranty Service 8
- Contents 9
- 14 Figures 14
- Tables 16
- Before you begin 17
- How to get help 18
- Preface 19 19
- Acronyms 20
- Chapter 1 21
- Overview 21
- R2MFC MBM faceplate elements 22
- System Status LEDs 23
- Config DIP switches 23
- RS232 port 24
- E1 Status LEDs 24
- Bantam jacks 24
- BNC and RJ-48 connectors 24
- Power connectors 24
- MBM DIP switches 25
- 26 Chapter 1 Overview 26
- Chapter 2 27
- Installation process map 28
- R2MFC MBM setup requirements 29
- Environment checklist 30
- Electrical requirements 30
- Software requirements 30
- Chapter 3 31
- Installing the R2MFC MBM 31
- Installing an R2MFC MBM 32
- Reconnecting the equipment 33
- Removing an R2MFC MBM 35
- Wiring an R2MFC MBM 37
- Chapter 4 41
- Configuring the R2MFC MBM 41
- Physical line characteristics 42
- E1 framing 42
- Line signaling 42
- Register signaling 43
- End of dialing (outgoing) 44
- Disable ANI 44
- Default category 44
- Default subscriber status 44
- Setting Config DIP switches 45
- E1 Framing 47
- Signaling 48
- Turning on second dial tone 52
- Chapter 5 55
- R2MFC MBM maintenance 55
- Clock synchronization 56
- Diagnostic tools 57
- Alarms Measurements 58
- Alarms propagation 59
- Faceplate LEDs 60
- Logs and traces 61
- Error messages 61
- Replacing an R2MFC MBM 62
- Upgrading firmware 63
- Chapter 6 67
- Command Line Interface (CLI) 67
- Accessing the CLI 68
- Commands 69
- LOad directory 69
- INfo directory 69
- VIew directory 70
- CNtrl directory 71
- COnfig directory 73
- ALarm directory 75
- SWerr directory 77
- MFC directory 78
- R2 directory 81
- PRI directory 83
- Appendix A 85
- Country code defaults 87
- MFC register signaling 88
- Mexico Config 2 89
- Brazil Config 1 92
- Brazil Config 2 94
- Argentina Config 1 96
- N0027684 01 100
- Appendix B 101
- Appendix C 103
- MFC Signal Definitions 103
- 104 MFC Signal Definitions 104
- Appendix D 105
- CLI Cable Pinout 105
- 106 CLI Cable Pinout 106
Minka Lavery 1424-281 manuales
Manuales del propietario y guías del usuario para No Minka Lavery 1424-281.
Ofrecemos 1 manuales en pdf Minka Lavery 1424-281 para descargar gratis por tipos de documentos: Manual de instrucciones
Kommentare zu diesen Handbüchern