Avaya Configuring Dial Services Bedienungsanleitung Seite 106
- Seite / 552
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring Dial Services
3-16
308621-14.00 Rev 00
Adding Lines to the Pool
To add a backup line to a pool, navigate to the backup-pool prompt and enter:
backup-line
<
line-type
>/<
slot/module/connector
>
To add a demand line to a pool, navigate to the demand-pool prompt and enter:
demand-line
<
line-type
>/<
slot/module/connector
>
line-type
indicates the interface type of the associated dial object. The value can be
serial, bri, or pri. For the ARN, use serial as the line type.
slot/module/connector identifies the physical interface. You specify a module
number only for ASN and System 5000 routers.
For example, to add the backup line (serial interface 1/1) to backup pool 8, enter:
backup-pool/8#
backup-line serial/1/1
backup-line/8/serial/1/1#
The pool ID becomes part of the backup-line and demand-line prompts
automatically.
If you defined multiple dial interfaces, you could add multiple lines to the same
pool, for example:
backup-pool/8#
backup-line serial/1/1; backup-line bri/3/1
Be aware of the following when selecting lines for a pool:
• All the lines in a demand pool must reside on the same slot and can combine
Raise DTR, V.25bis, Hayes, and ISDN lines.
• Do not use any lines previously configured as leased lines for the backup pool.
• The lines in a backup pool can reside across slots and can combine Raise
DTR, V.25bis, Hayes, and ISDN lines.
Go to one of the following sections:
• Specifying the ISDN Switch Type
on page 3-17
• Specifying the Authentication Protocol Information on page 3-20
- Configuring Dial Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308621-14.00 Rev 00 10
- Before You Begin 25
- Text Conventions 26
- Set Trap Monitor Filters 27
- Acronyms 28
- Hard-Copy Technical Manuals 30
- How to Get Help 30
- Chapter 1 31
- Dial Services Overview 31
- How to Use This Guide 32
- Nortel Networks Dial Services 33
- Dial-on-Demand Service 35
- Terminating Demand Circuits 36
- Demand Lines and Pools 38
- Demand Circuit Protocols 40
- Dial Backup Service 44
- Activating the Backup Line 45
- Backup Circuit Protocols 46
- Backup Lines and Pools 50
- Bandwidth-on-Demand Service 52
- Terminating Secondary Lines 55
- Chapter 2 59
- Starting Dial Services 59
- Setting Up a Dial Service 60
- Appendix A of this guide 63
- (Figure 2-1) 63
- Configuring Line Pools 64
- • Configuring BRI Lines 66
- on page 2-9 66
- Configuring BRI Lines 67
- Adding ISDN Lines to a Pool 71
- Configuring Circuits 72
- Enabling a Protocol 76
- Specifying the Backup Mode 78
- Creating Bandwidth Circuits 80
- Specifying the Bandwidth Mode 81
- Chapter 3 91
- <parameter> 93
- DS0037A 97
- Configuring a Modem Interface 100
- Configuring an ISDN Interface 102
- Configuring PRI Lines 104
- Creating a Line Pool 105
- Adding Lines to the Pool 106
- <mode> 109
- Protocols for Backup Circuits 110
- <string> 111
- What to Do Next 114
- Chapter 4 115
- ISDN Overview 115
- ISDN Standards 116
- Primary Rate Interface 117
- D Channel 117
- Figure 4-3. LAPD Frame 118
- ISDN Interfaces 119
- Reference Points 120
- Chapter 5 123
- Implementation Notes 123
- Types of Authentication 124
- WAN Encryption Protocol 128
- Asynchronous PPP 128
- ISDN Services 132
- Incoming Call Filtering 138
- Rate Adaption 139
- Example 2 140
- Chapter 6 143
- Standby Circuits 144
- How Standby Circuits Work 145
- Callback 147
- Configuring Callback 148
- Demand Circuit Groups 149
- Static Routes 150
- Dial-Optimized Routing 151
- Traffic Filters 154
- Data Compression 155
- PPP Multilink 156
- Protocol Prioritization 157
- Chapter 7 159
- Bandwidth for Backup Circuits 160
- Chapter 8 165
- Multilink Fragmentation 168
- How BAP Works 169
- Chapter 9 175
- Customizing Line Pools 175
- Changing Pool IDs 176
- Deleting Pools 176
- Using the BCC 177
- Using Site Manager 177
- <integer> 178
- Disabling MRU Compliance 181
- Chapter 10 183
- Customizing Modem Lines 183
- Modifying the Line Priority 187
- Using Modem Factory Defaults 189
- 34 characters 196
- is enabled or disabled 198
- For example: 198
- Resetting the Modem Remotely 200
- Chapter 11 205
- Customizing ISDN Lines 205
- Modifying the Adaption Rate 213
- Configuring the TEI Type 216
- Configuring the TEI Value 217
- Modifying the BRI T4 Timer 221
- Changing the Circuit Name 224
- Modifying the MTU 224
- Chapter 12 229
- Customizing Demand Circuits 229
- Adding a Service Record 233
- Adding or Modifying PVCs 234
- Retrying the Connection 239
- <text-string> 245
- Setting the Inactivity Mode 250
- Configuring Standby Circuits 254
- <failback_mode> 256
- <action> 257
- Enabling Callback 259
- Deleting a Schedule 273
- Removing Demand Circuits 280
- Deleting Hot Standby Circuits 281
- Chapter 13 283
- Customizing Backup Circuits 283
- <ID_number> 285
- ID_number 285
- Specifying the Redial Count 299
- (continued) 300
- To remove backup service: 305
- Chapter 14 307
- Chapter 15 317
- Customizing Phone Lists 317
- Local Phone Lists 319
- Adding Phone Numbers 320
- Changing the Remote Pool Type 329
- To set the remote pool type: 330
- Enabling PRI Multirate 332
- can be one of the following: 341
- To create a local phone list: 341
- Chapter 16 345
- Customizing Caller Resolution 345
- Configuring the CHAP Secret 348
- Configuring the PAP Password 348
- Appendix A 353
- Site Manager Parameters 353
- Caution: 355
- Pool ID Parameter 356
- External Modem Parameters 361
- V.34 Modem Parameters 367
- ISDN Switch Parameters 372
- BRI Configuration Parameters 379
- Figure A-11 407
- Parameters 434
- Local Phone Number Parameters 442
- Appendix B 463
- Configuration Examples 463
- Dial-on-Demand with PPP 464
- Demand Circuit Configuration 469
- Configuration of Router 1 473
- Configuration of Router 2 474
- Backup Pool Configuration 491
- backup-line bri/3/2/1 497
- Appendix C 507
- BCC show Commands 507
- show dial backup circuits 508
- Online Help for show Commands 509
- Commands for Dial-on-Demand 510
- Demand Circuit Information 512
- <circuit_name> 516
- -caller 517
- -circuit 518
- Commands for Dial Backup 519
- Modem Commands 530
- Receive Errors 533
- Transmit Errors 533
- System Errors 533
- Appendix D 537
- Ordering PRI Lines 538
- Appendix E 539
- (continued) 541
Verwandte Produkte und Handbücher für Software-Handbücher Avaya Configuring Dial Services
Software-Handbücher Avaya Configuring Interface and Router Redundancy Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Software-Handbücher Avaya Site Administration Reference Release 3.1 Bedienungsanleitung
(178 Seiten)
(178 Seiten)
Software-Handbücher Avaya Quick-Starting Routers (308654-14.20 Rev 00) Bedienungsanleitung
(134 Seiten)
(134 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern