Avaya Configuring ATM Services Bedienungsanleitung Seite 118
- Seite / 268
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring ATM Services
8-6 114056 Rev. A
Enabling or Disabling the VCC Timeout Period
When you enable the VCC Timeout Period (the default setting), the LEC may
release any unused Data Direct or Multicast Send VCCs after the VCC timeout
period expires. The ATM drivers provide a VCC timeout period of 20 minutes. If
you disable the VCC timeout period, the LEC does not release any unused Data
Direct VCCs.
Setting the Maximum Retry Count
The Maximum Retry Count is the maximum number of times a LEC can retry an
LE_ARP_REQUEST (following the original request) for any given frame MAC
address. You can allow either one (the default) or two retries.
Setting the Aging Time
The Aging Time defines the maximum amount of time that a LEC can maintain an
entry in its LE ARP cache without having to verify the relationship of that entry.
By default, the LEC maintains entries for 300 seconds. However, you can set the
aging time to a value from 10 through 300 seconds.
Setting the Forward Delay Time
While there are no changes occurring in the network topology, the Forward Delay
Time defines the maximum amount of time that a LEC can maintain an entry in its
LE ARP cache without having to verify the relationship of that entry.
By default, the LEC maintains entries for 15 seconds, so long as the network
topology does not change. However, you can set the Forward Delay Time to a
value from 4 through 30 seconds.
Site Manager: VCC Timeout Period Enable: page A-36
Site Manager: Max Retry Count: page A-37
Site Manager: Aging Time: page A-37
Site Manager: Forward Delay Time: page A-37
- Configuring ATM 1
- Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- 114056 Rev. A 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- World Wide Web 27
- Customer Service FTP 27
- Support Source CD 28
- CompuServe 28
- InfoFACTS 29
- How to Get Help 29
- Chapter 1 31
- Starting ATM 31
- Adding ATM to the Router 32
- Defining a Service Record 33
- 114056 Rev. A 1-5 35
- Supported Protocols 36
- Adding PVCs 38
- Chapter 2 41
- Understanding ATM Concepts 41
- 2-2 114056 Rev. A 42
- Figure 2-2. ATM Cell Header 42
- Data Transmission 43
- VP = Virtual path 44
- VC = Virtual channel 44
- Physical Layer 45
- ATM Layer 46
- ATM Adaptation Layer (AAL5) 47
- 2-8 114056 Rev. A 48
- Data Encapsulation 49
- 2-10 114056 Rev. A 50
- Encapsulation Rules for PVCs 52
- PVC Access Methods 53
- 2-14 114056 Rev. A 54
- Hybrid Access 55
- 2-16 114056 Rev. A 56
- Figure 2-8. Hybrid PVCs 56
- SVC Access Methods 58
- ATM Traffic Parameters 58
- Variable Bit Rate 59
- Available Bit Rate 59
- Rules for Editing Protocols 60
- ARP and Inverse ARP Support 60
- ATM Error Checking 61
- Converting Mb/s to Cells/s 61
- Example of an ATM Network 62
- Hardware Devices 64
- 2-26 114056 Rev. A 66
- For More Information 68
- Chapter 3 71
- 3-2 114056 Rev. A 72
- ATM Address Resolution 73
- 3-4 114056 Rev. A 74
- 114056 Rev. A 3-5 75
- Chapter 4 77
- LAN Emulation Components 78
- LAN Emulation Server 79
- Broadcast and Unknown Server 79
- 4-4 114056 Rev. A 80
- Initial State 81
- LECS Connect State 81
- Configure State 81
- Join State 81
- Initial Registration State 82
- BUS Connect State 82
- Operational State 82
- Chapter 5 85
- Customizing an ATM Line 85
- 5-2 114056 Rev. A 86
- Assigning the Framing Mode 87
- Defining ATM Cell Insertion 88
- Defining the Interface MTU 89
- 5-6 114056 Rev. A 90
- Specifying DS3 Line Build Out 92
- Chapter 6 95
- Service Records 95
- Autogenerating ATM Addresses 96
- Assigning ATM Addresses 97
- 6-4 114056 Rev. A 98
- Entering an Emulated LAN Name 100
- Defining an Emulated LAN Type 100
- Defining the MTU 101
- Where to Go Next 102
- Chapter 7 103
- Customizing PVCs 103
- Setting a VCI Number 104
- Setting the PCR 105
- Configuring ATM Services 106
- 7-4 114056 Rev. A 106
- Table 7-1. Valid PCR Ranges 106
- Setting the SCR 107
- 7-6 114056 Rev. A 108
- Table 7-2. Valid SCR Ranges 108
- Setting the MBS 109
- Setting the Transmit SDU Size 110
- Setting the Receive SDU Size 110
- Chapter 8 113
- Specifying an Owner 114
- Entering an ELAN Name 114
- Entering a LES ATM Address 114
- Selecting a Configuration Mode 115
- 8-4 114056 Rev. A 116
- Setting the Control Timeout 117
- Setting the Aging Time 118
- 114056 Rev. A 8-7 119
- Setting the Flush Timeout 120
- Entering a LECS ATM Address 121
- Chapter 9 123
- Customizing Signaling 123
- Assigning a Protocol Standard 124
- Setting Connection Thresholds 125
- Setting Signaling Timers 126
- 9-6 114056 Rev. A 128
- 9-8 114056 Rev. A 130
- Defining Retransmissions 131
- Pacing Calls 131
- Chapter 10 133
- Customizing ILMI 133
- Setting the ILMI Get Timer 134
- Setting the ILMI Set Timer 135
- Chapter 11 137
- Changing the ILMI VPI Number 138
- Changing the ILMI VCI Number 138
- Table 11-1. Valid PCR Ranges 139
- Table 11-2. Valid SCR Ranges 141
- Chapter 12 145
- Customizing SAAL 145
- Enabling or Disabling SAAL 146
- Modifying SAAL Timers 146
- Defining PDU Values 148
- Appendix A 151
- Site Manager Parameters 151
- A-2 114056 Rev. A 152
- Using the Menu Path 153
- A-4 114056 Rev. A 154
- 155
- 158
- 162
- A-14 114056 Rev. A 164
- A-18 114056 Rev. A 168
- 170
- A-22 114056 Rev. A 172
- 174
- A-26 114056 Rev. A 176
- A-28 114056 Rev. A 178
- A-30 114056 Rev. A 180
- 181
- 182
- A-34 114056 Rev. A 184
- A-38 114056 Rev. A 188
- A-40 114056 Rev. A 190
- 191
- A-42 114056 Rev. A 192
- A-44 114056 Rev. A 194
- A-46 114056 Rev. A 196
- A-48 114056 Rev. A 198
- A-50 114056 Rev. A 200
- ILMI category 202
- A-54 114056 Rev. A 204
- A-56 114056 Rev. A 206
- A-58 114056 Rev. A 208
- A-60 114056 Rev. A 210
- 212
- A-64 114056 Rev. A 214
- 216
- A-68 114056 Rev. A 218
- A-70 114056 Rev. A 220
- Appendix B 221
- B-2 114056 Rev. A 222
- ATM FRE2 Line Parameters 224
- ATM ARE Line Parameters 224
- (continued) 225
- B-6 114056 Rev. A 226
- Appendix C 229
- ATM Sample Log 229
- C-2 114056 Rev. A 230
- C-4 114056 Rev. A 232
- C-6 114056 Rev. A 234
- C-8 114056 Rev. A 236
- C-10 114056 Rev. A 238
- C-12 114056 Rev. A 240
- C-14 114056 Rev. A 242
- C-16 114056 Rev. A 244
- C-18 114056 Rev. A 246
- C-20 114056 Rev. A 248
- C-22 114056 Rev. A 250
- C-24 114056 Rev. A 252
- C-26 114056 Rev. A 254
- 114056 Rev. A Index-1 257
- 114056 Rev. A Index-3 259
- 114056 Rev. A Index-5 261
- 114056 Rev. A Index-7 263
- 114056 Rev. A Index-9 265
- 114056 Rev. A Index-11 267
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring ATM Services
Vernetzung Avaya R1.3 Konfigurationsanleitung
(13 Seiten)
(13 Seiten)
Vernetzung Avaya T1/E1 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Vernetzung Avaya BayRS, BCC, and Site Manager Software Version 15.0.0.0 Fixed Anomalies Bedienungsanleitung
(30 Seiten)
(30 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(272 Seiten)
(272 Seiten)
Vernetzung Avaya BCM200/400 Installationshandbuch
(374 Seiten)
(374 Seiten)
Vernetzung Avaya IPv6 Bedienungsanleitung
(162 Seiten)
(162 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern