Avaya Configuring DLSw Services Bedienungsanleitung Seite 71
- Seite / 204
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
DLSw Configuration Overview
3-15
• Source (Host) MAC (hex)
This parameter must be defined in the LAN gateway when using an IBM 3174
(or compatible) gateway. Other gateways typically do not define this value.
• Destination (Host) MAC (hex)
This parameter must match the MAC address of the LAN gateway, using
MSB (Token Ring) format.
• Source (Virtual) SAP (hex) and Destination (Host) SAP (hex)
These parameters must be entered into the SAP Table of the source and
destination routers. Both parameters default to 04. This value is included in
the default SAP Table.
For each local device you add, Site Manager creates a corresponding SDLC link
station, which is how SDLC sees the local device. Site Manager assigns several
default parameter values to the link station. For information on how to access and
change the link station parameters, see Configuring SDLC Services.
Once you add local devices, you can access and change the local device
parameters, as described in Chapter 5.
Optional Configuration Objects
Bay Networks routers in your network learn about the locations of remote
NetBIOS and SNA systems that are accessible through DLSw services in two
ways:
• Through a dynamic process, where DLSw inspects incoming frames to learn
the location of remote endstations.
• Through static definitions where the network administrator defines the
location of NetBIOS and SNA systems attached to remote LANs. Static
definitions are never required, but may be used to reduce the amount of
broadcast messages traversing the network.
Dynamically Learned Remote Systems
Bay Networks routers cache (dynamically learn) the MAC address and NetBIOS
name of remote systems.
- Configuring DLSw Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- About This Guide 17
- Before You Begin 18
- InfoFACTS 19
- World Wide Web 19
- How to Get Help 20
- Conventions 20
- Acronyms 21
- Chapter 1 23
- Data Link Switching Overview 23
- DLSw Networking Overview 24
- DLSw Single-Switch Services 27
- DLSw Dual Switch Services 28
- SDLC Support 30
- Integrated SDLC Conversion 31
- Frame Relay Support 33
- DLSw Filtering 35
- DLSw and Related Protocols 36
- Chapter 2 39
- DLSw Implementation Notes 39
- Counting SRB LANs and Bridges 40
- Counting the IP Virtual Ring 41
- Counting the Internal LAN 44
- Counting the DLSw Bridge 45
- Parallel Data Paths 47
- Source Routing Bridge 48
- Multiple DLSw Peers on a LAN 49
- DLSw and Bridging Services 49
- DLSw with Translation Bridge 51
- Memory Requirements 52
- TCP Considerations 53
- Flow Control 54
- LLC2 Flow Control 55
- TCP Flow Control 55
- Performance 56
- Chapter 3 57
- DLSw Configuration Overview 57
- DLSw SAP Table 61
- DLSw Slot Table 62
- DLSw Configuration Overview 63
- DLSw Peer IP Table 65
- Simplifying the Peer IP Table 66
- Configuration Objects for SDLC 68
- Local Devices 70
- Optional Configuration Objects 71
- Chapter 4 75
- Enabling DLSw Services 75
- 2. Click on OK 76
- Mapping Frame Relay Addresses 79
- Adding Slot IP Addresses 81
- Adding DLSw Peer IP Addresses 83
- 4. Click on Done 85
- Subsequent DLSw Configuration 99
- Chapter 5 101
- Editing DLSw Parameters 101
- Accessing DLSw Parameters 102
- (Figure 5-1) and then 103
- Select Protocols➔DLSw➔Global 103
- 3. Click on OK 104
- Enabling a DLSw Interface 113
- 1. Click on Add 118
- 3. Click on Done 121
- Click on Add 122
- 2. Click on Delete 125
- Adding a DLSw SAP Table Entry 127
- Click on Done 130
- 3. Click on Delete 131
- 2. Select the entry to edit 141
- Click on Apply 142
- Deleting DLSw from the Node 154
- Chapter 6 155
- Using DLSw Prioritization 155
- DLSw Priority Queues 157
- The Dequeuing Process 158
- The Dequeue List 159
- Weighted Dequeuing Algorithm 159
- Queue Depth 161
- Select ENABLED 164
- Click on OK 164
- 2. Click on Template 177
- Appendix A 187
- DLSw Default Settings 187
- Appendix B 191
- Predefined DLSw Criteria 192
- DLSw Reference Points 192
- Length (bits) 193
- Specifying MAC Address Ranges 194
- Table B-6. SAP Codes 196
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring DLSw Services
Vernetzung Avaya BCM200/400 Installationshandbuch
(386 Seiten)
(386 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(198 Seiten)
(198 Seiten)
Vernetzung Avaya BCM450 Konfigurationsanleitung
(11 Seiten)
(11 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Vernetzung Avaya Configuring Ethernet, FDDI, and Token Ring Services Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Avaya BayRS Version 15.1.0.0 Hinweis
(72 Seiten)
(72 Seiten)
(30 Seiten)
Vernetzung Avaya v5.0.450.2 Anwendungshinweis
(44 Seiten)
(44 Seiten)
Vernetzung Avaya BayRS Version 14.00 Hinweis
(64 Seiten)
(64 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern