Avaya Configuring Frame Relay Services Bedienungsanleitung Seite 126
- Seite / 240
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring Frame Relay Services
3-56
117376-C Rev. 00
both
outbound
inbound
either
For example, the following command line sets the inactivity direction to
outbound:
service/8.0.32# svc-inactivity-direction outbound
service/8.0.32#
Inactivity Values for an SVC
To set the inactivity timer and direction for a particular SVC option record:
1.
Navigate to the SVC options.
For example:
box; serial/3/2; frame-relay/3/2; service/8.0.32; svc-options/toronto
2.
Enter the
inactivity-timer
command with the value you want to use:
inactivity-timer
<integer>
<integer>
is the length of time, in seconds, before the SVC terminates because
no data has travelled over the circuit in the direction you specify in the
inactivity-direction attribute.
Legal timer values are 0 to 2147483647 seconds. The default is 60 seconds.
For example, the following command line sets the inactivity timer to 90
seconds:
service/8.0.32# inactivity-timer 90
service/8.0.32#
3.
Enter the
inactivity-direction
command with the value you want to use:
inactivity-direction
<value>
Legal direction values are:
both
outbound
inbound
either
For example, the following command line sets the inactivity direction to
outbound:
- Configuring 1
- Frame Relay Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117376-C Rev. 00 10
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 26
- Configuring an SVC 27
- Chapter 2 31
- Frame Relay Overview 31
- Introduction to Frame Relay 32
- Permanent Virtual Circuits 33
- Switched Virtual Circuits 33
- PVC and SVC Comparison 34
- Frame Relay Packets 35
- . Note, however 36
- Management Protocols 37
- BYS0037A 38
- LAPF Operational States 39
- SVC Signaling 41
- Call Setup 42
- Message Processing 43
- Frame Relay Service Records 44
- Frame Relay Access Modes 45
- Direct Access Mode 46
- Hybrid Access Mode 46
- Source Routing 48
- RFC 1490 48
- Address Resolution for PVCs 48
- Address Resolution for SVCs 49
- Traffic Control 50
- Data Compression 51
- Data Encryption 51
- Protocol Prioritization 51
- Traffic Shaping 53
- Quality of Service 55
- Traffic Shaping for SVCs 57
- Incoming 59
- Outgoing 59
- CIR Configuration Guidelines 60
- WCP and CIR Enforcement 60
- Oversubscribing the Interface 62
- X.213 Priority for SVCs 64
- Inactivity Timing for SVCs 64
- Multiline for PVCs 65
- PVC Pass-Through 67
- Frame Relay Dial Services 68
- Caution: 71
- Selecting a Management Type 72
- Selecting a DLCI Address Type 74
- Selecting Address Length 74
- Monitoring the Connection 76
- Polling Interval 77
- Full Enquiry Interval 77
- Customizing PVCs 81
- To delete PVCs: 87
- To move PVCs: 87
- Enabling Multicast 88
- Configuring PVC Pass-Through 90
- <integer> 100
- Enabling Compression for PVCs 102
- Using the BCC 103
- Using Site Manager 103
- Customizing SVCs 105
- For example: 107
- To delete service records: 107
- Call Screening and Blocking 108
- Disabling SVCs 112
- Disconnecting Active SVCs 114
- Setup Timer 121
- <value> 126
- (continued) 128
- Congestion Control 129
- Congestion Timer 130
- Congestion Counter 130
- Congestion Method 131
- To enable congestion control 134
- To enable traffic shaping 139
- To disable compression: 141
- To set X.213 priority value 143
- Deleting Frame Relay 144
- Customizing Frame Relay 145
- Appendix A 147
- Site Manager Parameters 147
- Figure A-2 148
- SVC LAPF Parameters 157
- SVC Signaling Parameters 163
- Parameters for PVCs 168
- PVC Service Record Parameters 172
- SVC Service Record Parameters 180
- SVC Options Parameters 186
- WHERE DOES THIS PARAMETER GO? 200
- Appendix B 201
- Table B-1. RIP Parameters 202
- Appendix C 209
- Monitoring Frame Relay Using 209
- BCC show Commands 209
- Commands for Frame Relay 210
- <option> 212
- <dlci> 215
- <name> 215
- ] [-service 216
- <multiline_name> 223
- <name> 228
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring Frame Relay Services
Vernetzung Avaya BCM 2.5 Betriebsanweisung
(50 Seiten)
(50 Seiten)
Vernetzung Avaya Glossary of Media Processing Server Series Terminology (Software Release 2.1) Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Vernetzung Avaya BayRS Version 15.2.0.0 Hinweis
(68 Seiten)
(68 Seiten)
Vernetzung Avaya Configuring Ethernet, FDDI, and Token Ring Services Bedienungsanleitung
(156 Seiten)
(156 Seiten)
Vernetzung Avaya BCM200/400 Installationshandbuch
(386 Seiten)
(386 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(198 Seiten)
(198 Seiten)
Vernetzung Avaya BCM450 Konfigurationsanleitung
(11 Seiten)
(11 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Vernetzung Avaya Configuring Ethernet, FDDI, and Token Ring Services Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Avaya BayRS Version 15.1.0.0 Hinweis
(72 Seiten)
(72 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern