Avaya Configuring Frame Relay Services Bedienungsanleitung Seite 29
- Seite / 240
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Starting Frame Relay
117376-C Rev. 00
1-9
Configuring Adjacent Hosts for an SVC
An adjacent host is a device on a locally attached network; it may or may not be a
router. You configure a MAC address for each adjacent host that does not
implement ARP, or to preempt the ARP process.
If you are configuring IP or IPX for this frame relay service record, see
Configuring IP Services or Configuring IPX Services for instruction on
configuring adjacent hosts.
Deleting Frame Relay from a Platform
To delete frame relay from all circuits on which it is currently configured:
5. Supply values for the following SVC
parameters. Use
Help
or the parameter
descriptions in Appendix A.
• SVC Local Party Number
•
SVC Local Party Sub-Address
(optional)
• SVC Local Party Number Plan
•
SVC Local Party Type of Number
6. Click on
Apply
. The SVC button replaces the Multiline
button in the Frame Relay Service List
window.
Site Manager Procedure
You do this System responds
1. Choose
Configuration Manager
>
Protocols
>
Frame Relay
>
Delete
Frame
Relay
.
A window prompts:
Do you REALLY
want to delete Frame Relay?
2. Click on
OK
. The Configuration Manager window
opens. Frame relay is no longer operating
on the platform.
Site Manager Procedure
(continued)
You do this System responds
- Configuring 1
- Frame Relay Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117376-C Rev. 00 10
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 26
- Configuring an SVC 27
- Chapter 2 31
- Frame Relay Overview 31
- Introduction to Frame Relay 32
- Permanent Virtual Circuits 33
- Switched Virtual Circuits 33
- PVC and SVC Comparison 34
- Frame Relay Packets 35
- . Note, however 36
- Management Protocols 37
- BYS0037A 38
- LAPF Operational States 39
- SVC Signaling 41
- Call Setup 42
- Message Processing 43
- Frame Relay Service Records 44
- Frame Relay Access Modes 45
- Direct Access Mode 46
- Hybrid Access Mode 46
- Source Routing 48
- RFC 1490 48
- Address Resolution for PVCs 48
- Address Resolution for SVCs 49
- Traffic Control 50
- Data Compression 51
- Data Encryption 51
- Protocol Prioritization 51
- Traffic Shaping 53
- Quality of Service 55
- Traffic Shaping for SVCs 57
- Incoming 59
- Outgoing 59
- CIR Configuration Guidelines 60
- WCP and CIR Enforcement 60
- Oversubscribing the Interface 62
- X.213 Priority for SVCs 64
- Inactivity Timing for SVCs 64
- Multiline for PVCs 65
- PVC Pass-Through 67
- Frame Relay Dial Services 68
- Caution: 71
- Selecting a Management Type 72
- Selecting a DLCI Address Type 74
- Selecting Address Length 74
- Monitoring the Connection 76
- Polling Interval 77
- Full Enquiry Interval 77
- Customizing PVCs 81
- To delete PVCs: 87
- To move PVCs: 87
- Enabling Multicast 88
- Configuring PVC Pass-Through 90
- <integer> 100
- Enabling Compression for PVCs 102
- Using the BCC 103
- Using Site Manager 103
- Customizing SVCs 105
- For example: 107
- To delete service records: 107
- Call Screening and Blocking 108
- Disabling SVCs 112
- Disconnecting Active SVCs 114
- Setup Timer 121
- <value> 126
- (continued) 128
- Congestion Control 129
- Congestion Timer 130
- Congestion Counter 130
- Congestion Method 131
- To enable congestion control 134
- To enable traffic shaping 139
- To disable compression: 141
- To set X.213 priority value 143
- Deleting Frame Relay 144
- Customizing Frame Relay 145
- Appendix A 147
- Site Manager Parameters 147
- Figure A-2 148
- SVC LAPF Parameters 157
- SVC Signaling Parameters 163
- Parameters for PVCs 168
- PVC Service Record Parameters 172
- SVC Service Record Parameters 180
- SVC Options Parameters 186
- WHERE DOES THIS PARAMETER GO? 200
- Appendix B 201
- Table B-1. RIP Parameters 202
- Appendix C 209
- Monitoring Frame Relay Using 209
- BCC show Commands 209
- Commands for Frame Relay 210
- <option> 212
- <dlci> 215
- <name> 215
- ] [-service 216
- <multiline_name> 223
- <name> 228
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring Frame Relay Services
Vernetzung Avaya BCM 2.5 Betriebsanweisung
(50 Seiten)
(50 Seiten)
Vernetzung Avaya Glossary of Media Processing Server Series Terminology (Software Release 2.1) Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Vernetzung Avaya BayRS Version 15.2.0.0 Hinweis
(68 Seiten)
(68 Seiten)
Vernetzung Avaya Configuring Ethernet, FDDI, and Token Ring Services Bedienungsanleitung
(156 Seiten)
(156 Seiten)
Vernetzung Avaya BCM200/400 Installationshandbuch
(386 Seiten)
(386 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(198 Seiten)
(198 Seiten)
Vernetzung Avaya BCM450 Konfigurationsanleitung
(11 Seiten)
(11 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Vernetzung Avaya Configuring Ethernet, FDDI, and Token Ring Services Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Vernetzung Avaya BayRS Version 15.1.0.0 Hinweis
(72 Seiten)
(72 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern