Avaya Configuring ATM Services Bedienungsanleitung Seite 100
- Seite / 310
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring ATM Services
5-16
When setting the SCR for ATM FRE2 ILI pairs, keep the following in mind:
• The SCR is essentially a future average. By setting the SCR you are
specifying the cell rate, over time, to which you want the VC to conform.
• To be useful, the SCR must not exceed the PCR.
• If you know the user average rate, set the SCR about 10% higher than this
value.
• ATM FRE2 ILI pairs require a minimum SCR value of 300 cells/s. PVCs may
fail to operate with SCR values less than 300 cells/s.
When setting the SCR for ATM ARE ILI pairs, keep the following in mind:
• The SCR maps directly to the MCR.
• The MCR provides guaranteed bandwidth for PVCs and Control VCs while
allowing sufficient bandwidth for SVCs to operate.
• To be useful, the SCR must not exceed the PCR.
• If you know the user average rate, set the SCR about 10% higher than this
value.
• ATM ARE ILI pairs require a minimum SCR value of 128 cells/s. VCs may
fail to operate with SCR values less than 128 cells/s.
• ATM ARE ILI pairs allow you to enter an SCR value of 0. Entering 0 for the
SCR turns off this function.
• The E-3 framing mode setting affects the maximum SCR setting. Refer to
Table 5-1 for additional information.
- Configuring ATM Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- About This Guide 19
- CompuServe 21
- InfoFACTS 21
- How to Get Help 22
- Conventions 22
- Acronyms 23
- Chapter 1 27
- ATM Overview 27
- Cell Header 28
- Cell Information Field 29
- ATM Layers 30
- Data Transmission 33
- ATM DXI versus ATM 34
- For More Information 35
- Chapter 2 37
- ATM DXI Support 38
- AAL Sublayer Support 39
- ATM DXI LMI Support 40
- ATM DXI Error Checking 40
- ATM DXI Implementation Notes 41
- ATM DXI Modes of Operation 42
- Group Access Mode 44
- Direct Access Mode 45
- Hybrid Access Mode 45
- Site A Site B 47
- Multipath Support 48
- Chapter 3 51
- Enabling ATM DXI Service 51
- Click on Add 55
- Chapter 4 59
- Editing ATM DXI Parameters 59
- 64
- Configuring PVCs 65
- 73
- 74
- Deleting PVCs 82
- Chapter 5 85
- ATM Support 86
- Multiprotocol Encapsulation 87
- ARP and Inverse ARP Support 88
- LAN Emulation 88
- ATM Signaling 89
- ATM Error Checking 90
- ATM Implementation Notes 91
- Hybrid Access 94
- SVC Access Methods 96
- ATM Traffic Parameters 96
- Converting Mb/s to Cells/s 97
- Variable Bit Rate 98
- Available Bit Rate 98
- Configuring ATM Services 100
- Maximum Burst Size 101
- Chapter 6 103
- Enabling ATM Service 103
- Enabling Overview 104
- Adding an ATM Circuit 104
- Click on OK 105
- Adding a Service Record 109
- Figure 6-4) 110
- 2. Click on Add 111
- 2. Click on OK 116
- Adding PVCs 118
- Chapter 7 121
- ATM Editing Basics 121
- Accessing ATM Windows 122
- Configuring 124
- Line Services 124
- Selecting Service Attributes 126
- Selecting Line Attributes 131
- Selecting ATM Signaling 132
- Selecting SAAL Attributes 134
- Selecting ILMI Attributes 136
- Assigning Data Encapsulation 138
- LANE 802.3 139
- LLC/SNAP Encapsulation 139
- Encapsulation Rules for PVCs 140
- Using ATM Protocol Menus 141
- Deleting Individual PVCs 149
- Click on PVC 150
- Click on Delete 150
- Site Manager deletes the PVC 150
- Deleting Individual SVCs 151
- Deleting ATM from the Router 154
- Chapter 8 155
- Editing Service Attributes 156
- Adding Service Records 157
- Figure 8-1) 158
- 162
- 163
- Adding or Copying PVCs 167
- Copying a PVC 169
- 7. Click on OK 170
- Editing PVC Parameters 172
- 8. Click on OK 174
- 183
- 183
- Chapter 9 195
- Click on Apply 210
- 216
- Editing ILMI Attributes 220
- Appendix A 231
- Appendix B 239
- ATM LAN Emulation Overview 239
- LAN Emulation Components 240
- LAN Emulation Server 241
- Broadcast and Unknown Server 241
- Initial State 243
- LECS Connect State 243
- Configure State 243
- Join State 243
- Initial Registration State 244
- BUS Connect State 244
- Operational State 244
- Appendix C 245
- ATM Address Resolution 247
- Adding an Adjacent Host 256
- 258
- Deleting an Adjacent Host 260
- Appendix D 265
- Sample ATM Network 265
- Hardware Devices 267
- Role of the CMS 269
- Role of the MCS 269
- Role of the ATM NMA 270
- Click on Service Attributes 271
- 10. Click on OK 274
- Appendix E 275
- ATM Sample Log 275
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring ATM Services
Vernetzung Avaya IPv6 Bedienungsanleitung
(162 Seiten)
(162 Seiten)
Vernetzung Avaya L2TP Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Vernetzung Avaya BCM450 Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Vernetzung Avaya BSGX4e Betriebsanweisung
(206 Seiten)
(206 Seiten)
Vernetzung Avaya Integrated Management Release 3.0 Standard Management Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Vernetzung Avaya a WAN Adapter Module in a BayStack ARN Router (114204 Rev. A) Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Vernetzung Avaya Business Communications Manager Telephone Anleitung zur Fehlerbehebung
(112 Seiten)
(112 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern