Avaya Configuring Frame Relay Services Bedienungsanleitung Seite 230
- Seite / 246
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring Frame Relay Services
C-12
308624-14.10 Rev 01
show frame-relay stats shaping
Displays high queue, normal queue, low queue, and summary traffic shaping
statistics for frame relay VCs.
The
show frame-relay stats shaping
command supports the following
subcommand options:
In addition, you can specify the following command filters and filter arguments
with the subcommand options:
The syntax and information for the shaping subcommand options is as follows:
RR Receive ready (RR) indicates that the station is ready to
receive information frames.
XID Exchange ID indicates the station’s identification
information.
high normal
low sum
-dlci
<dlci>
Displays only VCs with the specified DLCI.
-interface
<name>
Displays only VCs configured on the specified
interface.
-service
<name>
Displays only VCs on the specified service.
show frame-relay stats
shaping high
Displays high queue outbound traffic shaping statistics
for frame relay VCs.
show frame-relay stats
shaping low
Displays low queue outbound traffic shaping statistics
for frame relay VCs.
show frame-relay stats
shaping normal
Displays normal queue outbound traffic shaping
statistics for frame relay VCs.
show frame-relay stats
shaping sum
Displays a summary of traffic shaping statistics for
frame relay VCs.
- Configuring Frame Relay 1
- Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308624-14.10 Rev 01 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Hard-Copy Technical Manuals 21
- How to Get Help 22
- Chapter 1 23
- Frame Relay Overview 23
- Introduction to Frame Relay 24
- Permanent Virtual Circuits 25
- Switched Virtual Circuits 25
- PVC and SVC Comparison 26
- Frame Relay Packets 27
- . Note, however 28
- Management Protocols 29
- LAPF Operational States 31
- SVC Signaling 33
- Table 1-3. Network Timers 34
- Message Processing 35
- Frame Relay Service Records 36
- Frame Relay Access Modes 37
- Direct Access Mode 38
- Hybrid Access Mode 38
- Source Routing 40
- RFC 1490 40
- Address Resolution for PVCs 40
- Address Resolution for SVCs 41
- Traffic Control 41
- Data Compression 42
- Data Encryption 43
- Protocol Prioritization 43
- Congestion Control 44
- Traffic Shaping 45
- Quality of Service 47
- Traffic Shaping for SVCs 49
- Inactivity Timing for SVCs 55
- X.213 Priority for SVCs 55
- Multiline for PVCs 57
- PVC Pass-Through 59
- Frame Relay Dial Services 60
- Chapter 2 63
- Starting Frame Relay 63
- Configuring PVCs and SVCs 66
- To configure a PVC: 67
- Configuring an SVC 68
- Chapter 3 71
- Selecting a Management Type 72
- Setting XOFF Control 74
- Selecting a DLCI Address Type 75
- Monitoring the Connection 77
- Full Enquiry Interval 78
- Deleting Frame Relay 82
- Chapter 4 83
- Adding Service Records 85
- Deleting Service Records 86
- Enabling Multicast 92
- Configuring PVC Pass-Through 95
- Mapping Pass-Through PVCs 96
- Using Site Manager 100
- Using the BCC 100
- <integer> 101
- <value> 102
- Using Traffic Shaping 103
- Excess Burst 105
- Committed Burst 105
- CIR (Throughput) 106
- Customizing PVCs 109
- Removing Multiline Services 110
- Chapter 5 111
- Customizing SVCs 111
- Call Screening and Blocking 115
- SVC Screening 116
- SVC Screen Usage 116
- Disabling SVCs 119
- Disconnecting Active SVCs 120
- Station Type 122
- Initiation Mode 123
- Retransmission Timer 123
- Idle Timer 124
- Retransmission Limit 124
- Information Limit 124
- Window Size 125
- (continued) 126
- Maximum SVCs 128
- Setup Timer 128
- Disconnect Timer 129
- Release Timer 129
- Call Proceeding Timer 130
- Status Enquiry Timer 130
- Status Enquiry Retry 131
- <direction> 133
- Enabling Traffic Shaping 143
- Appendix A 155
- Site Manager Parameters 155
- Interface Parameters 156
- Figure A-2 157
- SVC LAPF Parameters 166
- SVC Signaling Parameters 171
- Service Name Parameter 176
- <line_number> 177
- <circuit_number> 177
- PVC Parameters 178
- PVC Service Record Parameters 180
- Multiline Algorithm Parameter 186
- C Service Record Parameters 189
- SVC Options Parameters 195
- Appendix B 211
- Table B-1. RIP Parameters 212
- Appendix C 219
- Monitoring Frame Relay Using 219
- Online Help for show Commands 220
- <dlci> 222
- <multiline_name> 222
- <name> 223
- (continued) 229
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring Frame Relay Services
Vernetzung Avaya BCM50 Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Vernetzung Avaya IPv6 Bedienungsanleitung
(157 Seiten)
(157 Seiten)
Vernetzung Avaya V.34 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung Avaya BayRS and BCC Software Version 15.4.0.1 Fixed Anomalies Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Vernetzung Avaya BCM450 Konfigurationsanleitung
(14 Seiten)
(14 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Vernetzung Avaya B179 Anwendungshinweis
(37 Seiten)
(37 Seiten)
Vernetzung Avaya BayRS Version 15.3.0.0 Hinweis
(74 Seiten)
(74 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern