Avaya Configuring Frame Relay Services Bedienungsanleitung Seite 43
- Seite / 246
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Frame Relay Overview
308624-14.10 Rev 01
1-21
To use data compression with frame relay, ensure that compression control is
enabled (the default) and select WCP as one of the protocols for the interface. For
more information about enabling compression, see “Disabling and Reenabling
Data Compression for PVCs” on page 4-26. For more information about data
compression, see Configuring Data Compression Services.
Data Encryption
Nortel Networks data encryption services enable you to protect sensitive traffic on
your network. Encryption for frame relay circuits works with direct mode PVCs
only. For information about and instructions for configuring data encryption, see
Configuring Data Encryption Services.
Protocol Prioritization
You can set priorities for the traffic sent across a synchronous line interface using
protocol prioritization, also called priority queueing. The ability to prioritize
traffic is important for an application that is time-sensitive and that requires a fast
response.
For example, a user at router A participating in a Telnet session with router B
requires a more immediate response than does a user at router A performing a file
transfer with router B.
When you select frame relay on a circuit, the router enables protocol prioritization
automatically. It does so because the DLCMI packets must have a higher priority
than any other packets you are sending across the network.
Enabling frame relay multiline affects protocol prioritization. For more
information, see “Protocol Prioritization and Multiline Incompatibility
” on
page 1-37
.
For information about configuring protocol prioritization, see Configuring Traffic
Filters and Protocol Prioritization.
- Configuring Frame Relay 1
- Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308624-14.10 Rev 01 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Hard-Copy Technical Manuals 21
- How to Get Help 22
- Chapter 1 23
- Frame Relay Overview 23
- Introduction to Frame Relay 24
- Permanent Virtual Circuits 25
- Switched Virtual Circuits 25
- PVC and SVC Comparison 26
- Frame Relay Packets 27
- . Note, however 28
- Management Protocols 29
- LAPF Operational States 31
- SVC Signaling 33
- Table 1-3. Network Timers 34
- Message Processing 35
- Frame Relay Service Records 36
- Frame Relay Access Modes 37
- Direct Access Mode 38
- Hybrid Access Mode 38
- Source Routing 40
- RFC 1490 40
- Address Resolution for PVCs 40
- Address Resolution for SVCs 41
- Traffic Control 41
- Data Compression 42
- Data Encryption 43
- Protocol Prioritization 43
- Congestion Control 44
- Traffic Shaping 45
- Quality of Service 47
- Traffic Shaping for SVCs 49
- Inactivity Timing for SVCs 55
- X.213 Priority for SVCs 55
- Multiline for PVCs 57
- PVC Pass-Through 59
- Frame Relay Dial Services 60
- Chapter 2 63
- Starting Frame Relay 63
- Configuring PVCs and SVCs 66
- To configure a PVC: 67
- Configuring an SVC 68
- Chapter 3 71
- Selecting a Management Type 72
- Setting XOFF Control 74
- Selecting a DLCI Address Type 75
- Monitoring the Connection 77
- Full Enquiry Interval 78
- Deleting Frame Relay 82
- Chapter 4 83
- Adding Service Records 85
- Deleting Service Records 86
- Enabling Multicast 92
- Configuring PVC Pass-Through 95
- Mapping Pass-Through PVCs 96
- Using Site Manager 100
- Using the BCC 100
- <integer> 101
- <value> 102
- Using Traffic Shaping 103
- Excess Burst 105
- Committed Burst 105
- CIR (Throughput) 106
- Customizing PVCs 109
- Removing Multiline Services 110
- Chapter 5 111
- Customizing SVCs 111
- Call Screening and Blocking 115
- SVC Screening 116
- SVC Screen Usage 116
- Disabling SVCs 119
- Disconnecting Active SVCs 120
- Station Type 122
- Initiation Mode 123
- Retransmission Timer 123
- Idle Timer 124
- Retransmission Limit 124
- Information Limit 124
- Window Size 125
- (continued) 126
- Maximum SVCs 128
- Setup Timer 128
- Disconnect Timer 129
- Release Timer 129
- Call Proceeding Timer 130
- Status Enquiry Timer 130
- Status Enquiry Retry 131
- <direction> 133
- Enabling Traffic Shaping 143
- Appendix A 155
- Site Manager Parameters 155
- Interface Parameters 156
- Figure A-2 157
- SVC LAPF Parameters 166
- SVC Signaling Parameters 171
- Service Name Parameter 176
- <line_number> 177
- <circuit_number> 177
- PVC Parameters 178
- PVC Service Record Parameters 180
- Multiline Algorithm Parameter 186
- C Service Record Parameters 189
- SVC Options Parameters 195
- Appendix B 211
- Table B-1. RIP Parameters 212
- Appendix C 219
- Monitoring Frame Relay Using 219
- Online Help for show Commands 220
- <dlci> 222
- <multiline_name> 222
- <name> 223
- (continued) 229
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring Frame Relay Services
Vernetzung Avaya BCM50 Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Vernetzung Avaya IPv6 Bedienungsanleitung
(157 Seiten)
(157 Seiten)
Vernetzung Avaya V.34 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung Avaya BayRS and BCC Software Version 15.4.0.1 Fixed Anomalies Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Vernetzung Avaya BCM450 Konfigurationsanleitung
(14 Seiten)
(14 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Vernetzung Avaya B179 Anwendungshinweis
(37 Seiten)
(37 Seiten)
Vernetzung Avaya BayRS Version 15.3.0.0 Hinweis
(74 Seiten)
(74 Seiten)
Minka Lavery 1423-281 manuales
Manuales del propietario y guías del usuario para No Minka Lavery 1423-281.
Ofrecemos 1 manuales en pdf Minka Lavery 1423-281 para descargar gratis por tipos de documentos: Guía de instalación
Kommentare zu diesen Handbüchern