Avaya Configuring Frame Relay Services Bedienungsanleitung Seite 92
- Seite / 246
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring Frame Relay Services
4-10
308624-14.10 Rev 01
Enabling Multicast
The multicast feature sets up a separate DLCI that replicates broadcast packets
and forwards them to the appropriate destinations. You can enable support for the
frame relay multicast service only if your frame relay provider offers multicasting.
You can use either the BCC or Site Manager to enable multicast service.
Using the BCC
To enable multicast service, you must set the
mutlicast-control
parameter for
both the interface and the PVC.
To enable multicast for the interface, navigate to the frame-relay prompt (for
example,
box; serial/1/2; frame-relay/1/2
) and enter:
multicast-control enabled
The default is
disabled
.
For example, the following command line enables multicast for this frame relay
interface:
frame-relay/1/2#
multicast-control enabled
frame-relay/1/2#
To enable multicast for the PVC, navigate to the prompt for the PVC that you
want to configure as multicast (for example,
box; serial/1/2; frame-relay/1/2;
service/4.0.32; pvc/1/2/51
) and enter:
multicast-control enabled
The default is
disabled
.
For example, the following command line enables multicast for this PVC:
pvc/1/2/51#
multicast-control enabled
pvc/1/2/51#
- Configuring Frame Relay 1
- Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308624-14.10 Rev 01 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Hard-Copy Technical Manuals 21
- How to Get Help 22
- Chapter 1 23
- Frame Relay Overview 23
- Introduction to Frame Relay 24
- Permanent Virtual Circuits 25
- Switched Virtual Circuits 25
- PVC and SVC Comparison 26
- Frame Relay Packets 27
- . Note, however 28
- Management Protocols 29
- LAPF Operational States 31
- SVC Signaling 33
- Table 1-3. Network Timers 34
- Message Processing 35
- Frame Relay Service Records 36
- Frame Relay Access Modes 37
- Direct Access Mode 38
- Hybrid Access Mode 38
- Source Routing 40
- RFC 1490 40
- Address Resolution for PVCs 40
- Address Resolution for SVCs 41
- Traffic Control 41
- Data Compression 42
- Data Encryption 43
- Protocol Prioritization 43
- Congestion Control 44
- Traffic Shaping 45
- Quality of Service 47
- Traffic Shaping for SVCs 49
- Inactivity Timing for SVCs 55
- X.213 Priority for SVCs 55
- Multiline for PVCs 57
- PVC Pass-Through 59
- Frame Relay Dial Services 60
- Chapter 2 63
- Starting Frame Relay 63
- Configuring PVCs and SVCs 66
- To configure a PVC: 67
- Configuring an SVC 68
- Chapter 3 71
- Selecting a Management Type 72
- Setting XOFF Control 74
- Selecting a DLCI Address Type 75
- Monitoring the Connection 77
- Full Enquiry Interval 78
- Deleting Frame Relay 82
- Chapter 4 83
- Adding Service Records 85
- Deleting Service Records 86
- Enabling Multicast 92
- Configuring PVC Pass-Through 95
- Mapping Pass-Through PVCs 96
- Using Site Manager 100
- Using the BCC 100
- <integer> 101
- <value> 102
- Using Traffic Shaping 103
- Excess Burst 105
- Committed Burst 105
- CIR (Throughput) 106
- Customizing PVCs 109
- Removing Multiline Services 110
- Chapter 5 111
- Customizing SVCs 111
- Call Screening and Blocking 115
- SVC Screening 116
- SVC Screen Usage 116
- Disabling SVCs 119
- Disconnecting Active SVCs 120
- Station Type 122
- Initiation Mode 123
- Retransmission Timer 123
- Idle Timer 124
- Retransmission Limit 124
- Information Limit 124
- Window Size 125
- (continued) 126
- Maximum SVCs 128
- Setup Timer 128
- Disconnect Timer 129
- Release Timer 129
- Call Proceeding Timer 130
- Status Enquiry Timer 130
- Status Enquiry Retry 131
- <direction> 133
- Enabling Traffic Shaping 143
- Appendix A 155
- Site Manager Parameters 155
- Interface Parameters 156
- Figure A-2 157
- SVC LAPF Parameters 166
- SVC Signaling Parameters 171
- Service Name Parameter 176
- <line_number> 177
- <circuit_number> 177
- PVC Parameters 178
- PVC Service Record Parameters 180
- Multiline Algorithm Parameter 186
- C Service Record Parameters 189
- SVC Options Parameters 195
- Appendix B 211
- Table B-1. RIP Parameters 212
- Appendix C 219
- Monitoring Frame Relay Using 219
- Online Help for show Commands 220
- <dlci> 222
- <multiline_name> 222
- <name> 223
- (continued) 229
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring Frame Relay Services
Vernetzung Avaya BCM50 Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Vernetzung Avaya IPv6 Bedienungsanleitung
(157 Seiten)
(157 Seiten)
Vernetzung Avaya V.34 Bedienungsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung Avaya BayRS and BCC Software Version 15.4.0.1 Fixed Anomalies Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Vernetzung Avaya BCM450 Konfigurationsanleitung
(14 Seiten)
(14 Seiten)
Vernetzung Avaya X.25 Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Vernetzung Avaya B179 Anwendungshinweis
(37 Seiten)
(37 Seiten)
Vernetzung Avaya BayRS Version 15.3.0.0 Hinweis
(74 Seiten)
(74 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern