Avaya Configuring Dial Services Bedienungsanleitung Seite 466
- Seite / 482
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring Dial Services
D-2
117353-B Rev. 00
Ordering PRI Lines
When ordering ISDN PRI lines for use in the United States, note the following:
• The switch must be a DMS-100, AT&T 5ESS, or AT&T 4ESS switch.
• Configure all 23 B channels for Circuit Switched Data (CSD).
• Configure the D channel for signaling only.
• You cannot run the National ISDN-2 (NI-2) protocol.
Table D-2. BRI Parameters for the Northern Telecom DMS-100 Switch
Parameter Value Notes
Signaling Functional
Protocol Version 1 or 2 1 is NT1 Custom,
2 is NI-1 (National ISDN-1)
TEI Assignment Dynamic
Maximum # of Keys 3 Specify any number equal to or greater than
1
Release Key is N or a Key
Number
No Not relevant for proper operation
Ring Indicator is Y/N No Not relevant for proper operation
EKTS is Y/N No
- Configuring 1
- Dial Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117353-B Rev. 00 10
- About This Guide 23
- Before You Begin 24
- Conventions 24
- Acronyms 25
- Bay Networks Customer Service 27
- How to Get Help 27
- Chapter 1 29
- Dial Services Overview 29
- How to Use This Guide 30
- Bay Networks Dial Services 31
- Dial-on-Demand Service 33
- Demand Lines and Pools 34
- Demand Circuit Protocols 36
- Activating Demand Circuits 38
- Terminating Demand Circuits 39
- Dial Backup Service 42
- Figure 1-8 44
- Backup Lines and Pools 46
- Activating the Backup Line 48
- Bandwidth-on-Demand Service 50
- Terminating Secondary Lines 54
- Chapter 2 57
- Starting Dial Services 57
- Setting Up a Dial Service 58
- Appendix A of this guide 61
- (Figure 2-1) 61
- Configuring Line Pools 62
- Configuring BRI Lines 64
- Configuring PRI Lines 66
- Configuring WAN Line 67
- Services 67
- Adding ISDN Lines to a Pool 68
- Configuring Circuits 70
- Enabling a Protocol 73
- Creating Dial Backup Circuits 74
- Specifying the Backup Mode 75
- Creating Bandwidth Circuits 77
- Specifying the Bandwidth Mode 78
- Chapter 3 87
- Starting Dial Backup 87
- Configuring WAN Line Services 89
- DS0036A 91
- Create a Dial Object 94
- Create a Backup Line Pool 95
- Add a Backup Line to the Pool 96
- Configure BRI Lines 97
- Configure PRI Lines 99
- Specify the ISDN Switch Type 100
- Configuring Dial Services 102
- What to Do Next 105
- Chapter 4 107
- ISDN Overview 107
- ISDN Standards 108
- Primary Rate Interface 109
- The D Channel 109
- Figure 4-3. LAPD Frame 110
- ISDN Interfaces 111
- Reference Points 112
- Chapter 5 115
- Implementation Notes 115
- Types of Authentication 116
- Asynchronous PPP 120
- RADIUS Accounting Services 123
- ISDN Services 123
- Incoming Call Filtering 129
- Rate Adaption 130
- Example 2 131
- Chapter 6 135
- How Standby Circuits Work 137
- Callback 142
- Configuring Callback 143
- Demand Circuit Groups 145
- Static Routes 149
- Dial Optimized Routing 149
- Data Compression 153
- PPP Multilink 154
- Protocol Prioritization 154
- Chapter 7 157
- Bandwidth for Backup Circuits 158
- Chapter 8 163
- Multilink Fragmentation 166
- How BAP Works 167
- Chapter 9 173
- Customizing Line Pools 173
- Modifying Line Pools 174
- Changing Pool IDs 175
- Deleting Pools 175
- For example: 176
- To delete any type of pool: 176
- Using the BCC 177
- Using Site Manager 178
- Modifying the Line Priority 184
- Using Modem Factory Defaults 186
- Selecting a Modem Type 194
- Remotely Resetting the Modem 200
- Enabling RFC 1661 Compliance 205
- Modifying ISDN Configurations 206
- Modifying the Adaption Rate 213
- To modify the X.25 circuit: 224
- Deleting BRI 228
- Deleting PRI 229
- Chapter 10 231
- Customizing Demand Circuits 231
- Removing Demand Circuits 246
- Chapter 11 247
- Customizing Backup Circuits 247
- <ID_number> 249
- <mode> 249
- Frame Relay Services 250
- Specifying the Redial Count 263
- (continued) 265
- To remove backup service: 270
- Chapter 12 271
- Chapter 13 281
- Customizing Phone Lists 281
- Caution: 282
- Local Phone Lists 283
- Adding Phone Numbers 284
- To set the adaption rate: 293
- Changing the Remote Pool Type 294
- To set the connection type: 296
- Enabling PRI Multirate 297
- To enable PRI multirate: 298
- To create a local phone list: 305
- Chapter 14 309
- Customizing Caller Resolution 309
- Appendix A 315
- Dial Service Parameters 315
- Pool ID Parameter 318
- External Modem Parameters 323
- V.34 Modem Parameters 329
- ISDN Switch Parameters 334
- BRI Configuration Parameters 341
- Relay window is similar 346
- Local Phone Number Parameters 403
- Appendix B 423
- Configuration Examples 423
- Dial-on-Demand with PPP 424
- Table B-3. IP Parameters 426
- Configuration of Router 1 429
- Configuration of Router 2 429
- Demand Circuit Configuration 431
- Table B-13. IP Parameters 432
- Appendix C 453
- Show Commands for Dial Backup 453
- Sample Output 454
- Online Help for show Commands 454
- Commands for Dial Backup 455
- show dial backup summary 456
- >] [-circuit < 457
- Line Information: (Serial) 458
- Appendix D 465
- Ordering PRI Lines 466
- Appendix E 467
- (continued) 469
Verwandte Produkte und Handbücher für Software Avaya Configuring Dial Services
(100 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern