Avaya Configuring Dial Services Bedienungsanleitung Seite 143
- Seite / 258
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring Circuits
5-7
Parameter: Connection Mode
Default: Collision Master
Options: No Dial | Collision Master | Collision Slave
Function: Determines the role of a router when two routers try to establish a demand
circuit with each other. Both routers in a demand configuration can
initiate a call. This parameter determines which router places the call first,
to prevent both routers from placing the call at the same time.
Instructions: To avoid continual collisions, configure one router as Collision Master
and the other as Collision Slave. To ensure that a router receives calls, but
never initiates calls, enter No Dial. Calls are then made only in one
direction.
If this circuit is part of an unnumbered demand circuit group, the router
automatically sets this parameter to No Dial because a circuit in a demand
circuit group cannot initiate a call.a
MIB Object ID: 1.3.6.1.4.1.18.3.5.1.4.5.1.28
Parameter: Auto Demand Termination
Default: Disabled
Options: Enabled | Disabled
Function: For applications where there are two paths to the same destination, this
parameter allows the router to automatically terminate a failed demand
circuit and send the data over an alternate path to the destination. Note
that the router does not terminate the circuit until it reaches the maximum
connection attempts, which you specify in the Retry Max parameter.
Enable this parameter when the router continues to advertise a static route
over a demand circuit, but the router cannot establish a connection over
that circuit. The router terminates the demand circuit, which notifies the
routing protocol that the static routes associated with this circuit are no
longer active. The router then uses the alternate path.
Instructions: Select Enable if you have an alternate path to a remote destination and
you want to ensure that if the demand circuit fails, the router terminates
the circuit and sends data over the alternate path to the destination.
MIB Object ID: 1.3.6.1.4.1.18.3.5.1.4.5.1.29
- Configuring Dial Services 1
- Bay Networks Software License 3
- Contents 5
- About This Guide 19
- CompuServe 21
- InfoFACTS 22
- World Wide Web 22
- How to Get Help 23
- Conventions 23
- Acronyms 24
- Chapter 1 27
- Dial Services Overview 27
- Dial-on-Demand Service 29
- Demand Lines and Pools 30
- Activating Demand Circuits 32
- Dial Backup Service 34
- Backup Lines and Pools 36
- Activating the Backup Line 37
- Bandwidth-on-Demand Service 38
- Activating Secondary Lines 40
- Terminating Secondary Lines 40
- Chapter 2 43
- ISDN Overview 43
- ISDN Standards 44
- Primary Rate Interface 45
- The D Channel 45
- Figure 2-3. LAPD Frame 46
- ISDN Interfaces 47
- Reference Points 48
- Chapter 3 51
- Implementation Notes 51
- D Channel Support 52
- B Channel Support 52
- S/T Interfaces 53
- BRI Subaddresses 54
- Selective PRI Service 55
- Call Screening 56
- Rate Adaption 56
- Example 1 57
- Example 2 57
- Point-to-Point Protocol 58
- IP Adjacent Hosts 61
- Data Compression 62
- PPP Multilink 63
- Static Routes 64
- Protocol Prioritization 65
- Breath-of-Life Messages 67
- Bandwidth for Backup Circuits 68
- Chapter 4 79
- Using the MIB Object ID 80
- Configuring Line Pools 80
- Pool ID Parameter 86
- Line Media Type Parameters 86
- Adding Line Pools 87
- Configuring ISDN Lines 91
- PRI Physical Interfaces 93
- MCT1/MCE1 Clock Parameters 97
- MCT1/MCE1 Port Parameters 98
- MCT1 Port Parameters 100
- Creating Line Pools 101
- Configuring Dial Services 102
- MCE1 Port Parameters 105
- MCT1/MCE1 Logical Lines 108
- Logical Lines Parameter 111
- (continued) 113
- (continued) 114
- Configuring ISDN Logical Lines 116
- Logical Lines Parameters 118
- fills in the fields below it 121
- Local Phone Number Parameters 123
- Changing a Line Pool 127
- Changing Lines in a Pool 128
- Port Parameters 134
- Timeslots 134
- Chapter 5 137
- Configuring Circuits 137
- Interface for Dialup Lines 139
- Demand Circuit Parameters 140
- Configuring Circuits 141
- Click on Done 151
- Schedule Parameters 152
- Deleting Demand Circuits 155
- 4. Click on OK to save 157
- Providing Backup Circuits 164
- Click on OK 166
- Circuit Options Parameters 168
- Primary Circuit Parameters 169
- (Figure 5-19) 175
- (Figure 5-20) 176
- Manager window 176
- Deleting Backup Circuits 178
- Click on Done to exit 182
- Congestion Monitor Parameters 189
- (Figure 5-26) 194
- Chapter 6 197
- Configuring Phone Lists 197
- Configuring Phone Lists 199
- Chapter 7 209
- Caller Resolution Table 209
- (Figure 7-2) 210
- Appendix A 217
- Configuration Examples 217
- Dial-on-Demand Using PPP 218
- Demand Pools Configuration 219
- Demand Circuit Configuration 220
- Configuration Examples 221
- Configuration of Router 1 222
- Configuration of Router 2 223
- Demand Pool Configuration 224
- Outgoing Phone List 225
- Protocol Configuration 226
- Backup Circuit Configuration 230
- Backup Pool Configuration 235
- Type)➔Circuit Options window 236
- Appendix B 239
- Appendix C 247
Verwandte Produkte und Handbücher für Software Avaya Configuring Dial Services
Software Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Bedienungsanleitung
(188 Seiten)
(188 Seiten)
Software Avaya CS1000 Bedienungsanleitung
(180 Seiten)
(180 Seiten)
Software Avaya Business Communications Manager - Personal Call Manager Betriebsanweisung
(90 Seiten)
(90 Seiten)
Software Avaya v4.1 Bedienungsanleitung
(166 Seiten)
(166 Seiten)
Software Avaya 4n(114973-A Hinweis
(60 Seiten)
(60 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern