Avaya Configuring WAN Line Services Bedienungsanleitung Seite 125
- Seite / 294
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring MCE1 and MCT1 Services
117345-B Rev. 00
7-13
See the Line Coding parameter on page A-30 for information.
Setting the Signal Level
The Signal Level parameter specifies the T1 transmit power level in decibels (dB).
Line buildout conditions the signals to mitigate attenuation. Line buildout also
depends on the physical length of the T1 line.
The carrier determines signal levels on a long-haul (0 to 6000 ft. of cable) T1
network interface. If 0.0 dB is not sufficient for long-haul, the carrier determines
values of -15 and -7.5 dB.
Signal power for DSX-1 short-haul (0 to 655 ft.) is based on cable length.
For DSX-1, decibel levels correspond to cable length, as follows:
• 0.0 dB -- 0 to 133 ft.
• 0.5 dB -- 133 to 255 ft.
• 0.8 dB -- 255 to 399 ft.
• 1.1 dB -- 399 to 533 ft.
• 1.5 dB -- 533 to 655 ft.
By default, the signal level is set to 0.0 dB. Set the long-haul or short-haul signal
level for this MCT1 interface according to the length of the cable or as the carrier
specifies.
See the Signal Level (dB) parameter on page A-31
for information.
Setting the Alarm Threshold Time
By default, the MCT1 interface waits 2 seconds before logging a performance
defect or anomaly as an event message. Change the alarm threshold time to any
value from 2 to 10 seconds.
See the Setup Alarm Threshold (seconds) parameter on page A-31
for
information.
- Configuring 1
- WAN Line Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117345-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 24
- Chapter 1 27
- Getting Started 27
- To edit a circuit: 33
- Figure 1-4. Edit Lines Window 34
- Chapter 2 35
- Setting the BofL Timeout 41
- Setting the MTU 41
- Configuring Clocking Signals 43
- Setting the Signal Mode 45
- Setting Minimum Frame Spacing 49
- Setting the CRC Size 52
- Setting the Signaling Method 54
- Setting the Line Coding 55
- Configuring KG84A Security 55
- Setting the Retry Count 59
- Setting the Link Idle Timer 60
- Setting the Cable Type 61
- Setting the Retry Timer 61
- Setting a Priority 62
- Setting the Hold Down Time 63
- Setting the IFTF Pattern 65
- Chapter 3 77
- Asynchronous Services 77
- for information 78
- Setting the Remote IP Address 79
- Specifying the Remote Port 80
- Specifying the Local Port 80
- Setting the Idle Timer 81
- Chapter 4 83
- Setting the Option Mode 85
- Loopback Test Modes 89
- AN/ANH/ARN 90
- Chapter 5 93
- Enabling or Disabling BofL 96
- Using the BCC 100
- Using Site Manager 100
- Configuring HSSI Services 101
- Chapter 6 103
- Editing T1 Services 104
- Setting the T1 Frame Type 105
- Configuring WAN Line Services 106
- Figure 6-2. Bipolar Format 106
- Specifying Line Buildout 107
- Assigning Channel Functions 108
- Editing E1 Services 109
- Enabling or Disabling CRC 111
- Setting the Clock Source 111
- Chapter 7 113
- Setting the Clock Parameters 116
- Configuring a DS0A Connection 129
- Setting Parameters 131
- Table 7-2 132
- Defining Logical Lines 133
- (MCT1 Example) 134
- Circuit Name: MCE1_31_1 135
- Circuit name: MCE1_231_1 135
- (MCE1 Example) 136
- See the following sections: 137
- Caution: 139
- Assigning Timeslots 144
- About the Tests 149
- Setting Port Test Parameters 150
- Running Port Tests 153
- Running Logical Line Tests 158
- Send Command Function 159
- Chapter 8 161
- Configuring FT1 Services 161
- Configuring an FT1 Port 162
- Defining Logical Line 172
- Circuit name: 174
- Chapter 9 189
- Types of Multiline Circuits 190
- Multiline Example 191
- Software Considerations 192
- Logical Lines (MCE1 Example) 205
- Appendix A 209
- Asynchronous Line Parameters 210
- DSU/CSU Parameters 216
- E1 Line Parameters 218
- HSSI Line Parameters 221
- LAPB Parameters 226
- MCE1 Port Parameters 233
- MCT1 Port Parameters 237
- FT1 Port Parameters 252
- FT1 Logical Line Parameters 258
- Synchronous Line Parameters 263
- T1 Line Parameters 282
- Glossary 287
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring WAN Line Services
Vernetzung Avaya X.25 Bedienungsanleitung
(148 Seiten)
(148 Seiten)
Vernetzung Avaya BCM1000 Installationshandbuch
(90 Seiten)
(90 Seiten)
Vernetzung Avaya BCM3.x Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Vernetzung Avaya V.34 Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Vernetzung Avaya 1D5 Hinweis
(40 Seiten)
(40 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern