Avaya Configuring WAN Line Services Bedienungsanleitung Seite 250
- Seite / 294
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring WAN Line Services
A-42
117345-B Rev. 00
Parameter: NRZI Enable
Path: Configured QMCT1 Connector > MCT1 Logical Lines
Default: Disable
Options: Enable
|
Disable
Function: The software uses this parameter only if you installed a QMCT1 DS0A link
module. Disable specifies no communication of state changes between the
subscriber’s devices over the frame relay network. Enable specifies NRZI line
encoding to communicate such state changes.
Instructions: If you are configuring the router connection to the host side, and the NRZI
settings of the host and CPE match, use the Disable setting. If they do not match,
set this parameter to Enable.
If you are configuring the router connection to the remote access side, and the
NRZI settings of the controller and CPE match, use the Disable setting. If they
do not match, set this parameter to Enable.
MIB Object ID: 1.3.6.1.4.1.18.3.4.9.6.1.66
Parameter: NRZI Type
Path: Configured QMCT1 Connector > MCT1 Logical Lines
Default: Mark
Options: Mark
|
Space
Function: The software uses this parameter only if you installed a QMCT1 DS0A link
module and you set the NRZI Enable parameter to Enable. This parameter
specifies the NRZI encoding type in the frame on the logical line. The Mark
format uses a 0-bit to indicate a state change and a 1-bit to indicate no state
change; the Space format uses the opposite.
Instructions: Ignore this parameter if you set NRZI Enable to Disable.
Otherwise, if you are configuring the router connection to
• The host side, determine which device on that side is using NRZI, and match
this parameter to the encoding type used by that device
• The remote access side, determine which device on that side is using NRZI,
and match this parameter to the encoding type used by that device
MIB Object ID: 1.3.6.1.4.1.18.3.4.9.6.1.67
- Configuring 1
- WAN Line Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117345-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 24
- Chapter 1 27
- Getting Started 27
- To edit a circuit: 33
- Figure 1-4. Edit Lines Window 34
- Chapter 2 35
- Setting the BofL Timeout 41
- Setting the MTU 41
- Configuring Clocking Signals 43
- Setting the Signal Mode 45
- Setting Minimum Frame Spacing 49
- Setting the CRC Size 52
- Setting the Signaling Method 54
- Setting the Line Coding 55
- Configuring KG84A Security 55
- Setting the Retry Count 59
- Setting the Link Idle Timer 60
- Setting the Cable Type 61
- Setting the Retry Timer 61
- Setting a Priority 62
- Setting the Hold Down Time 63
- Setting the IFTF Pattern 65
- Chapter 3 77
- Asynchronous Services 77
- for information 78
- Setting the Remote IP Address 79
- Specifying the Remote Port 80
- Specifying the Local Port 80
- Setting the Idle Timer 81
- Chapter 4 83
- Setting the Option Mode 85
- Loopback Test Modes 89
- AN/ANH/ARN 90
- Chapter 5 93
- Enabling or Disabling BofL 96
- Using the BCC 100
- Using Site Manager 100
- Configuring HSSI Services 101
- Chapter 6 103
- Editing T1 Services 104
- Setting the T1 Frame Type 105
- Configuring WAN Line Services 106
- Figure 6-2. Bipolar Format 106
- Specifying Line Buildout 107
- Assigning Channel Functions 108
- Editing E1 Services 109
- Enabling or Disabling CRC 111
- Setting the Clock Source 111
- Chapter 7 113
- Setting the Clock Parameters 116
- Configuring a DS0A Connection 129
- Setting Parameters 131
- Table 7-2 132
- Defining Logical Lines 133
- (MCT1 Example) 134
- Circuit Name: MCE1_31_1 135
- Circuit name: MCE1_231_1 135
- (MCE1 Example) 136
- See the following sections: 137
- Caution: 139
- Assigning Timeslots 144
- About the Tests 149
- Setting Port Test Parameters 150
- Running Port Tests 153
- Running Logical Line Tests 158
- Send Command Function 159
- Chapter 8 161
- Configuring FT1 Services 161
- Configuring an FT1 Port 162
- Defining Logical Line 172
- Circuit name: 174
- Chapter 9 189
- Types of Multiline Circuits 190
- Multiline Example 191
- Software Considerations 192
- Logical Lines (MCE1 Example) 205
- Appendix A 209
- Asynchronous Line Parameters 210
- DSU/CSU Parameters 216
- E1 Line Parameters 218
- HSSI Line Parameters 221
- LAPB Parameters 226
- MCE1 Port Parameters 233
- MCT1 Port Parameters 237
- FT1 Port Parameters 252
- FT1 Logical Line Parameters 258
- Synchronous Line Parameters 263
- T1 Line Parameters 282
- Glossary 287
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring WAN Line Services
Vernetzung Avaya X.25 Bedienungsanleitung
(148 Seiten)
(148 Seiten)
Vernetzung Avaya BCM1000 Installationshandbuch
(90 Seiten)
(90 Seiten)
Vernetzung Avaya BCM3.x Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Vernetzung Avaya V.34 Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Vernetzung Avaya 1D5 Hinweis
(40 Seiten)
(40 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern