Avaya Configuring Line Services Bedienungsanleitung Seite 112
- Seite / 301
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Customizing Synchronous and Asynchronous Interfaces
114078 Rev. A 5-17
Setting the Signal Mode
You use the Signal Mode parameter to set either Balanced or Unbalanced
transmission on an interface, depending on the signaling mode of the connected
device.
Balanced transmission uses two conductors to carry signals; unbalanced
transmission uses one conductor to carry a signal, with a ground providing the
return path.
You can set Balanced or Unbalanced transmission for the interface.
Enabling or Disabling RTS Signals
The RTS Enable parameter enables or disables the detection of request to send
(RTS) signals on this interface.
Set this parameter to Enable if the connected device (for example, a modem or a
KG84A cryptographic device) uses RTS/CTS flow control.
You can enable or disable RTS signals for the interface.
Enabling or Disabling DMA Burst Cycles
The Burst Count parameter specifies single or multiple DMA burst cycles.With
this parameter set to Enable, the chip performs eight-word bursts. With the
parameter set to Disable, the chip performs single-word burst cycles.
This is a performance-tuning parameter. Set it to Enable except when configuring
an interface on these link modules:
• DSDE (5430 - Dual Synchronous, Dual Ethernet)
• DSE (5420 - Dual Synchronous, Single Ethernet)
Set it to Disable if excessive TxUflo or RxOflo errors occur on the Ethernet ports.
Site Manager: Signal Mode parameter: page A-58
Site Manager: RTS Enable parameter: page A-59
- Configuring Line 1
- Services 1
- Bay Networks Software License 3
- Contents 5
- 114078 Rev. A vii 7
- 114078 Rev. A ix 9
- 114078 Rev. A 10
- 114078 Rev. A xi 11
- 114078 Rev. A xiii 13
- 114078 Rev. A xv 15
- 114078 Rev. A xvii 17
- 114078 Rev. A xix 19
- About This Guide 21
- Before You Begin 22
- Conventions 22
- Acronyms 23
- 114078 Rev. A xxv 25
- Bay Networks Customer Service 26
- World Wide Web 27
- Customer Service FTP 27
- Support Source CD 28
- CompuServe 28
- InfoFACTS 29
- How to Get Help 29
- Chapter 1 31
- Getting Started 31
- 1-2 114078 Rev. A 32
- Click on Edit 33
- (Figure 1-3) 33
- Select Lines > Edit Lines 34
- The Edit Lines window appears 34
- Chapter 2 37
- About Line Protocols 37
- Ethernet Overview 38
- 2-4 114078 Rev. A 40
- ConcentratorConcentrator 41
- 2-6 114078 Rev. A 42
- 2-8 114078 Rev. A 44
- Station Timers 45
- 2-10 114078 Rev. A 46
- SMT Frame Services 47
- 2-12 114078 Rev. A 48
- Token Ring Overview 49
- 2-14 114078 Rev. A 50
- Figure 2-7. Token Ring LAN 50
- Overview of WAN Protocols 51
- HSSI Overview 52
- ISDN Overview 52
- MCE1 and MCT1 Overview 53
- Synchronous Overview 54
- T1 Overview 54
- Figure 2-8. D4 Frame 55
- 2-20 114078 Rev. A 56
- Figure 2-10. Bipolar Format 57
- Chapter 3 58
- Customizing LAN Interfaces 58
- Setting the BofL Interval 59
- 3-4 114078 Rev. A 61
- 3-6 114078 Rev. A 63
- Editing FDDI Lines 65
- 3-10 114078 Rev. A 67
- 2. Click on SMT Attributes 67
- 3-12 114078 Rev. A 69
- 3-14 114078 Rev. A 71
- Editing FDDI Path Attributes 72
- 3-16 114078 Rev. A 73
- 2. Click on Path Attributes 73
- Editing FDDI Port Attributes 74
- Editing Token Ring Lines 75
- Specifying the Ring Speed 76
- Chapter 4 78
- Customizing WAN Interfaces 78
- 4-2 114078 Rev. A 79
- Setting the Framing Mode 81
- Editing ATM FRE-2 Lines 83
- 4-8 114078 Rev. A 85
- Editing E1 Lines 87
- Assigning Channel Functions 88
- Editing HSSI Lines 89
- 4-14 114078 Rev. A 91
- Editing T1 Lines 93
- Chapter 5 96
- Customizing Synchronous and 96
- Asynchronous Interfaces 96
- Specifying the Start Protocol 97
- 114078 Rev. A 5-3 98
- Setting the Baud Rate 99
- Setting the Idle Timer 99
- 114078 Rev. A 5-5 100
- Configuring Line Services 101
- 5-6 114078 Rev. A 101
- 114078 Rev. A 5-7 102
- Setting the Station Type 103
- Setting the Control Field 103
- Setting the Window Size 104
- Setting the N2 Retry Count 104
- Setting the Link Setup Action 105
- 114078 Rev. A 5-11 106
- Editing Synchronous Lines 107
- 114078 Rev. A 5-13 108
- Setting the BofL Timeout 109
- Setting the Clock Source 110
- 5-16 114078 Rev. A 111
- Setting the Signal Mode 112
- 5-18 114078 Rev. A 113
- Setting Minimum Frame Spacing 114
- 5-20 114078 Rev. A 115
- 114078 Rev. A 5-21 116
- Setting the CRC Size 117
- Setting the Signaling Method 117
- Setting the Line Coding 118
- Setting the Retry Count 119
- Setting the Link Idle Timer 119
- Setting the Cable Type 120
- Setting the Retry Timer 120
- Setting Sync Priority 121
- Configuring KG84A Security 122
- LS0017A 123
- 114078 Rev. A 5-29 124
- 5-30 114078 Rev. A 125
- Chapter 6 126
- Setting the Clock Parameters 128
- Customizing MCE1 Port Details 129
- 114078 Rev. A 6-5 130
- 6-6 114078 Rev. A 131
- Customizing MCT1 Port Details 132
- 6-8 114078 Rev. A 133
- 114078 Rev. A 6-9 134
- 6-10 114078 Rev. A 135
- 114078 Rev. A 6-11 136
- 6-12 114078 Rev. A 137
- 114078 Rev. A 6-13 138
- Defining Logical Lines 140
- (MCE1 example) 142
- Customizing Logical Lines 143
- 114078 Rev. A 6-19 144
- 6-20 114078 Rev. A 145
- 114078 Rev. A 6-21 146
- 6-22 114078 Rev. A 147
- 114078 Rev. A 6-23 148
- 6-24 114078 Rev. A 149
- Assigning Timeslots 150
- 2. Click on B-Channels 152
- 114078 Rev. A 6-29 154
- Chapter 7 156
- Configuring Multiline Services 156
- Multiline Example 157
- Types of Multiline Circuits 158
- Grouping Data Paths 159
- Multiline Traffic Distribution 160
- Frame Relay Considerations 161
- PPP Multilink 161
- Configuring Multiline 162
- 114078 Rev. A 7-9 164
- 114078 Rev. A 7-11 166
- 114078 Rev. A 7-13 168
- 114078 Rev. A 7-15 170
- Select File > Exit 171
- (Figure 7-12) 171
- 114078 Rev. A 7-17 172
- Chapter 8 174
- Managing Line Resources 174
- Line Resource Manager (LRM) 175
- Starting the LRM 176
- Configuring the LRM 179
- 8-8 114078 Rev. A 181
- 8-10 114078 Rev. A 183
- 114078 Rev. A 8-11 184
- Deleting LRM Services 185
- 5. Click on OK 186
- Appendix A 188
- 189
- 190
- 190
- 191
- A-6 114078 Rev. A 193
- A-10 114078 Rev. A 197
- 114078 Rev. A A-11 198
- 200
- 200
- 202
- A-16 114078 Rev. A 203
- 114078 Rev. A A-17 204
- A-18 114078 Rev. A 205
- 209
- 213
- 214
- 215
- A-30 114078 Rev. A 217
- 218
- 219
- 220
- A-34 114078 Rev. A 221
- 114078 Rev. A A-35 222
- 223
- 114078 Rev. A A-37 224
- 225
- 227
- 227
- 228
- 232
- 234
- 236
- A-50 114078 Rev. A 237
- 238
- 240
- A-54 114078 Rev. A 241
- A-56 114078 Rev. A 243
- 244
- 245
- 245
- 247
- A-62 114078 Rev. A 249
- 114078 Rev. A A-63 250
- 252
- A-66 114078 Rev. A 253
- 255
- 255
- 256
- A-70 114078 Rev. A 257
- 258
- 259
- 114078 Rev. A A-73 260
- 261
- 114078 Rev. A A-75 262
- 263
- 263
- 114078 Rev. A A-77 264
- 266
- A-80 114078 Rev. A 267
- Appendix B 268
- Asynchronous Line Parameters 269
- ATM FRE-2 Line Parameters 269
- ATM ARE Line Parameters 270
- E1 Line Parameters 271
- FDDI Line Parameters 272
- HSSI Line Parameters 273
- LAPB Parameters 274
- MCE1 Line Parameters 274
- (continued) 275
- (continued) 276
- T1 Line Parameters 281
- Token Ring Line Parameters 281
- Multiline Parameters 281
- Table B-30. LRM Parameters 282
- Appendix C 284
- Setting Test Parameters 285
- 114078 Rev. A C-3 286
- Setting the BERT Alarm Type 287
- Setting the BERT Test Pattern 287
- Setting the Line Type 288
- C-6 114078 Rev. A 289
- Running Port Tests 290
- C-8 114078 Rev. A 291
- 114078 Rev. A C-9 292
- 114078 Rev. A Index-1 294
- 114078 Rev. A Index-3 296
- 114078 Rev. A Index-5 298
- 114078 Rev. A Index-7 300
Verwandte Produkte und Handbücher für Vernetzung Avaya Configuring Line Services
Vernetzung Avaya IPv6 Bedienungsanleitung
(162 Seiten)
(162 Seiten)
Vernetzung Avaya L2TP Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Vernetzung Avaya BCM450 Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Vernetzung Avaya BSGX4e Betriebsanweisung
(206 Seiten)
(206 Seiten)
Vernetzung Avaya Integrated Management Release 3.0 Standard Management Bedienungsanleitung
(52 Seiten)
(52 Seiten)
Vernetzung Avaya a WAN Adapter Module in a BayStack ARN Router (114204 Rev. A) Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Vernetzung Avaya Business Communications Manager Telephone Anleitung zur Fehlerbehebung
(112 Seiten)
(112 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern